manualshive.com logo in svg

Shuttle AV18E, User Manual

Share
Download
Shuttle AV18E User Manual Download Page 4

- 2 -

STEP 11 Connect External Peripherals to Back Panel............................. 20

STEP 12 First Time System Boot Up....................................................... 22

STEP 13 Install Drivers & Software Components ..................................... 23

3.2 JUMPER SETTINGS .................................................................................. 24

Jumpers & Connectors Guide.................................................................. 25

EEPROM FLASH BLOCK LOCK (JP6) .................................................. 27

CPU Clock Ratio Setting (JP4)................................................................ 27

Clear CMOS (JP2) .................................................................................. 28

System Frequency Configuration (JP7) ................................................... 29

PS/2 Keyboard & PS/2 Mouse Connectors ............................................. 30

USB1 / USB2 Port Connectors ................................................................ 30

COM1 / COM2 Connectors ..................................................................... 30

Parallel Port Connector ........................................................................... 30

Line-Out and Line-In and Mic-In Header ................................................... 31

MIDI/GAME Port...................................................................................... 31

Hardware Reset Connector (RST) ........................................................... 32

HDD LED Connector (HDLED) ............................................................... 32

Green LED Connector (GLED) ................................................................ 32

EPMI Connector (EPMI) .......................................................................... 32

ATX Power On/Off Switch Connector (PWON) ......................................... 33

Speaker Connector (SPEAKER)............................................................. 33

PWR LED Connector (POWER LED) ..................................................... 33

Enhanced IDE and Floppy Connectors .................................................... 34

Audio Connector CD_IN (JP10) .............................................................. 34

Audio Connector TAD I/O (JP11) ............................................................. 35

Audio Connector AUX (JP12).................................................................. 35

External USB Ports (JP5) ........................................................................ 35

Summary of Contents for AV18E










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands