background image

10

Setting IntelliMix

The SCM820 uses IntelliMix to select channels to open in a mix, while attenuating the gain of closed channels. IntelliMix is available in three presets and 

can be customized to excel in any application where multiple microphones are used at once. In all modes (except Manual), 

MaxBus 

ensures that only one 

channel is opened per sound source. 

Channel Gain in Classic Mixer

1 Talker

Full gain is applied as the 

channel opens; off attenuation 

gain is applied to all channels.

2+ Talkers

As additional channels open, 

NOMA factor decreases the 

level of all channels.

Smooth

Smooth dynamically balances system gain between open and closed 

channels. The system gain remains consistent by distributing gain across 

channels to equal one open channel. It incorporates IntelliMix operating 

principles into a gain sharing mixing style, making it ideal for broadcast and 

recording applications.

Gating Style: 

Relative

Gain Scaling: 

Adaptive

Off Attenuation: 

Disabled

Last Mic Lock On: 

Disabled

Tip: 

Unroute all unused channels to the mix bus. This will ensure the 

most consistent noise floor in Smooth mode. 

Channel Gain in Smooth Mixer

1 Talker

Relative gain is applied to the 

open channel; all channels 

adaptively attenuate to maintain 

system gain.

2+ Talkers

As additional channels open, 

gain is adaptively distributed 

across all channels to 

maintain system gain.

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

Mixer Mode Descriptions

The SCM820 features five mix modes: Classic, Extreme, Smooth, Custom or Manual.

Classic

Classic mode emulates the classic Shure SCM810 automixer (in its default 

settings). It is renowned for fast-acting, seamless channel gating and 

consistent perceived ambient sound levels. The Classic mode excels in 

most applications, specifically sound reinforcement and teleconferencing.

Gating Style:

Full

Gain Scaling:

Fixed

Off Attenuation:

−15 dB

Last Mic Lock On:

Enabled

Extreme

Extreme is an aggressive variation of the Classic mode, configured to 

achieve maximum gain before feedback by completely attenuating closed 

channels. Only open channels add to the system levels and ambient sound. 

Extreme mode is designed for sound reinforcement applications.

Gating Style: 

Full

Gain Scaling: 

Fixed

Off Attenuation: 

−110 dB

Last Mic Lock On: 

Disabled

Channel Gain in Extreme Mixer

1 Talker

Full gain is applied to the 

open channel. Closed 

channels are fully attenuated.

2+ Talkers

As additional channels open, 

NOMA factor decreases the 

level of all channels.

Manual

Manual mode deactivates IntelliMix to allow the SCM820 to operate as a 

standard mixer. All Channel Status LEDs remain on in this mode to indicate 

there is no IntelliMix attenuation. Channel and mix equalization, output 

limiter and mix bus routing are still active in this setting. 

Tip: 

Be careful when switching to Manual mode, as all microphones will 

gate open to full gain, which may result in feedback. 

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

-15 dB

Custom

Custom mode allows IntelliMix parameters to be fine-tuned and tailored from 

the GUI. The mixer automatically switches to Custom once a parameter 

is changed in Classic, Extreme or Smooth mode. Theses configurations 

are saved to the device and will persist after the mixer is turned off and 

restarted. Custom configurations can also be saved as a file to a computer 

and loaded onto the device for quick recall. 

Summary of Contents for SCM820-DAN





































Reviews: