2
2
CONNECTING THE HARDWARE ADAPTER
TO THE DFR11EQ
Once the switch assembly and hardware adapter are
connected, plug the hardware adapter of the DRS-10 into
the RS232 port of the DFR11EQ (see Figure 3).
Ñ
Ñ
Ñ
ÑÑ
ÑÑ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
ÑÑ
Ñ
Ñ
Ñ
Ñ
ÑÑ
Ñ
ÑÑ
ÑÑ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
ÑÑ
Ñ
Ñ
ÑÑ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
Ñ
DFR11EQ BACK PANEL
HARDWARE ADAPTER
CONNECTING THE HARDWARE ADAPTER
FIGURE 3
MOUNTING THE DRS-10 SWITCH ASSEMBLY
TO A WALL
The switching assembly of the DRS-10 may be
mounted using the supplied mounting kit (Figure 4):
1.
Mount a standard electrical box into the wall.
2.
Place the position ring onto the switch assembly, fitting
the tab of the ring into the desired numbered groove on
the switch assembly.
NOTE: The switch assembly of the DRS-10 can be cus-
tomized to select up to ten scenes. The location of the
position ring determines how many scenes the switch is
able to access.
3.
Peel the plastic sheath from the affixed labels on the wall
plate and hardware adapter. A second 10-position label
is provided for use on custom wall plates.
4.
Insert the switch assembly post through the lock washer
and wall plate and attach with the supplied washer and
nut, being careful not to over-tighten the nut.
5.
Press the supplied knob onto the switch assembly post.
6.
Secure the wire cable to the switch assembly using the
two screw terminals on the back of the assembly, as
previously described in Figure 1.
7.
Mount the assembly to the electrical box in the wall.
SWITCH ASSEMBLY
POSITION RING
WALL PLATE
LABEL
NUT
KNOB
WASHER
LOCK WASHER
DRS-10 WALL MOUNTING ASSEMBLY
FIGURE 4
SPECIFICATIONS
Connectors
DFR11EQ connection: Male 9-pin D sub-connector
Cable connection: Screw terminals
Case
Plastic housing
Dimensions
Hardware Adapter: 6.3 cm L x 3.3 cm W x 1.6 cm H
(2.5 in. L x 1.3 in. W x .65 in. H)
Mounting Assembly: 12 cm H x 7.4 cm W x 4.7 cm D
(4.75 in. H x 2.94 in. W x 1.87 in. D)
Cable
Maximum Resistance: 100 ohms series between switch
and hardware adapter
Maximum Length: at least 914 m (3,000 ft.)
Certification
Tested to comply with FCC standards. FOR HOME OR
OFFICE USE. This product complies with part 15 of the
FCC rules. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by Shure
Incorporated could void your authority to operate this equip-
ment.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to ra-
dio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment
and the receiver
Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected
Consult the dealer or an experienced radio/TV tech-
nician for help
This class B digital apparatus complies with Canadian
ICES-003.
Conforms to European EMC Directive 89/336/EEC: Pro-
fessional Audio Products Standard EN 55103 (1996); Part
1 (emissions) and Part 2 (immunity). The DRS-10 is in-
tended for use in environments E1 (residential) and E2 (light
industrial) as defined in European EMC standard EN 55103.
It meets the applicable tests and performance criteria found
in the standard for these environments. EMC conformance
is based on the use of recommended cables.
Replacement Parts
Hardware Adapter Kit
RPC601
. . . . . . . . . . . . . . . . . . . . .
Switch Assembly Kit
RPC603
. . . . . . . . . . . . . . . . . . . . . .
Wall Plate Kit
RPC602
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
