background image

SR501 EN Operation Manual 

- 25 - 

 

time section of thermostat heating) 

►Press “SET” button, hour “00” blinks 

►Press “▲▼” button, to adjust hour. 

►Press “SET” button, minute “00” blinks 

►Press “▲▼” button, to adjust minute. 

►Press “SET” button, temperature “55

o

C

” blinks 

►Press  “▲▼”  button,  to  adjust  switch-on  temperature,  adjustable  range  is 

0-93

o

C, factory set is 55

o

C. 

►Press “SET” or “ESC” button to confirm the setting. 

►Press  “▲”  button,  “tH1F  23:59”  displays  on  the 

screen  (end  time  of  the  1st  time  section  of  thermostat 

heating). 

Repeat above steps to set the ending  time and ending temperature of the 1st 

time section.   

►Press “▲” button, “tH2O 00:00” displays on the screen (start time of the 2nd 

time  section  of  thermostat  heating),  repeat  above  steps  to  set  time  and 

temperature of 2nd and 3rd time sections.   

 

         

Note:

  if  water  level  is  below  50%,  to  avoid  dry  heating,  it  is  needed  to 

trigger water filling and fill water position above 50% level.   

6.2 LWPR Low water pressure   

Description: 

During  the  water  filling  process,  due  to  low  water  pressure  or  water  supply 

stopping  (water 

level  can’t  be  raised  to  the  upper  level  within  60  minutes), 

controller will trigger the low water pressure protection function, and 

“low water 

pressure”  signal  shows  on  the  screen,  to  avoid  damaging  the  solenoid  valve 

due to its long-time running, the protection function will be deactivated after 60 

minutes   

 

Summary of Contents for SR501

















































Reviews: