background image

 

Operating Determinations 

 

This device is not designed for permanent operation. Consistent operation breaks will ensure that the 
device will serve you for a long time without defects. 

 

The minimum distance between light-output and the illuminated surface must be more than 0.5 meter. 

 

The maximum ambient temperature 

t

a

 = 45°C must never be exceeded. 

 

The relative humidity must not exceed 50 % with an ambient temperature of 45° C. 

 

If this device is operated in any other way, than the one described in this manual, the product may 
suffer damages and the

 

warranty becomes void. 

 

Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc. 

 

You endanger your own safety and the safety of others! 

 

Improper installation can cause serious damage to people and property ! 

 

 

Rigging

 

Please follow the European and national guidelines concerning rigging, trussing and all other 
safety issues. 

 

Do not attempt the installation yourself ! 
Always let the installation be carried out by an authorized dealer !

 

 

Procedure: 

 

If the LED Par 56 Short Pro is lowered from the ceiling or high joists, professional trussing systems 
have to be used. 

 

Use a clamp to mount the LED Par 56 Short Pro, with the mounting-bracket, to the trussing system. 

 

The LED Par 56 Short Pro must never be fixed swinging freely in the room.  

 

The installation must always be secured with a safety attachment, e.g. an appropriate safety net 
or safety-cable. 

 

When rigging, derigging or servicing the LED Par 56 Short Pro, always make sure, that the area 
below the installation place is blocked and staying in the area is forbidden.

 

 

 

 

 

The LED Par 56 Short Pro can be mounted in a hanging position (Fig. Above) or Upright (Fig. Below), using 
the support brackets. Mounting the LED Par 56 Short Pro with a clamp or any other mounting bracket is 
recommended, depending on the requirements of your application. 

 

 

 

The LED Par 56 Short Pro can be placed on a flat stage floor or mounted to any kind of truss by a clamp. 

 

Improper installation can cause serious damage to people and property ! 
 

 

Summary of Contents for led par 56 short pro rgb




















Reviews: