(3) Push the mode button till the display shows o-s. Now you can select if the
unit should as automatic unit (o-a) or as slave unit (o-d). You can select the
master or slave mode by using the up or down key.
(4) Push the mode button till the display shows A and a two digit number. Eg.
A03.
(5) Select the desired programm by pushing the up or down button.
You can select 64 preprogrammed programms.
(6) The fixture will start to move his automatic programm.
Setting up your Firestorm for Slave Control
(1) Fasten the effect light onto firm trussing (Use a 30-kg rated or stronger C-
clamp fastened onto the Firestorm bracket). Leave at least one meter on all
sides for air circulation.
(2) Plug one end of the electric mains power cord into the IEC socket on the
unit. (See figure 6, page 13.) Then plug the other end of the cord into a
proper electric power supply socket.
(3) Link up all the units by DMX cables (we recommend DAP cables)
(4) Push the mode button till the display shows o-s. Now you can select if the
unit should as master unit (o-s) or as slave unit (o-d). You can select the
master or slave mode by using the up or down key.
When the master fixture is in auto-mode all the units will run the build-in
programm on a fixed speed. If the master fixture is set up as a slave unit all
the fixtures will react to the speed of music.
(5) The master unit will always send 20 channels DMX out to controll the slave
units. Therefore it is important to give a slave fixture an DMX address as
well.
Push the mode button till the display shows a three digit number. Eg. 001.
Select the desired address by the up and down button.
See the diagram below to select the correct DMX address in slave mode.
Fixture
S lave Address Slave Channel
Master Slave relation
1
001
1,2,3,4,5
Same
2
006
6,7,8,9,10
Tilt, gobo, color, gobo rot is same
Pan is invert
3
011
11,12,13,14,15 Gobo, color, gobo rot is same
Pan and tilt are inverted
4
016
16,17,18,19,20 Pan gobo, color, gobo rot is same
Tilt is invert
Setting up your Firestorm for Slave Control
(1) Fasten the effect light onto firm trussing (Use a 30-kg rated or stronger C-
clamp fastened onto the Firestorm bracket). Leave at least one meter on all
sides for air circulation.
(2) Plug one end of the electric mains power cord into the IEC socket on the unit.
(See figure 6, page 13.) Then plug the other end of the cord into a proper
electric power supply socket.
(3) Link up all the units by DMX cables (we recommend DAP cables)
(4) Push the mode button till the display shows o-s. Now you can select if the
unit should as master unit (o-s) or as slave unit (o-d). Select o-d which
enables the fixture to receive DMX signal
(5) Push the mode button till the display show a three digit number. E.g 002
(6)Select the desired DMX address by using the up and down keys.
Your fixture is now ready for use with DMX
Note: Make sure that the first scanner in the line is be adressed as Master
fixture !!
Changing the programms speed in Auto mode
(1) Push the mode button till the display shows U-X. Where X stands for a
Number.
(2) Select the right speed bu pushing the up- and down button (1-8)
(3) The scanner will adjust the speed of the step.
Pan invert of the scanner in DMX mode
(1) Push the mode button till the display shows P-n or P-F.
(2) Select the right mode by using the up and down button. P-n means normal
use and P-F means pan invert.
Tilt invert of the scanner in DMX mode
(1) Push the mode button till the display shows t-n or t-F.
(2) Select the right mode by using the up and down button. t-n means normal
use and t-F means pan invert
6
5
