background image

 

20 

No Response to DMX 

Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card 
malfunction. 

1.

 

Check the DMX setting. Make sure that DMX addresses are correct. 

2.

 

Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power. 
Try your DMX control again. 

3.

 

Determine whether the controller or light effect is at fault. Does the controller operate properly with 
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light 
effect to a qualified technician. 

 

See the table below for more problem solving. 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Problem 

Probable cause(s) 

Remedy 

One or more 
fixtures are 
completely dead. 

No power to the fixture 
 

• Check that power is switched on 

and cables are plugged in. 

Fixtures reset 
correctly, but all 
respond 
erratically or not 
at all to the 
controller. 

The controller is not connected. 

• Connect controller.  

3-pin XLR Out of the controller 
does not match XLR Out of the first 
fixture on the link (i.e. signal is 
reversed). 

• Install a phase reversing cable 

between the controller and the first 
fixture on the link. 

 
 
 
 
 
 
 
 

 

Fixtures reset 
correctly, but 
some respond 
erratically or not 
at all to the 
controller. 

 
 
 
Poor data quality 

• Check data quality. If much lower 

than 100 percent, the problem may 
be a bad data link connection, poor 
quality or broken cables, missing 
termination plug, or a defective 
fixture disturbing the link. 

 
Bad data link connection 

• Inspect connections and cables. 

Correct poor connections. Repair or 
replace damaged cables.  

Data link not terminated with 120 
Ohm termination plug. 

• Insert termination plug in output jack 

of the last fixture on the link. 

Incorrect addressing of the fixtures.  • Check address setting.  
 

 

One of the fixtures is defective and 
disturbs data transmission on the 
link. 

• Bypass one fixture at a time until 

normal operation is regained: unplug 
both connectors and connect them 
directly together. 

• Have the defective fixture serviced 

by a qualified technician.  

 
3-pin XLR Out on the fixtures does 
not match (pins 2 and 3 reversed). 

• Install a phase-reversing cable 

between the fixtures or swap pin 2 
and 3 in the fixture, that behaves 
erratically.  

 
 
 
 

 

No light 

 
 
Fixture is too hot. 

• Allow fixture to cool. 
• Clean fan. 
• Make sure air vents at control panel 

and front lens are not blocked. 

•  Turn up the air conditioning. 

 

LEDs damaged 

• Disconnect fixture and return to your 

dealer. 

The power supply settings do not 
match local AC voltage and 
frequency. 

• Disconnect fixture. Check settings 

and correct if necessary. 

 

Summary of Contents for Calypso 43104
























Reviews: