SHOWTEC 50444 User Manual Download Page 8

 

 

 

7 

 

  

 

 

TED Pack Single 

Product code: 50444 

 

Attention 
Power supply 

 

Before connecting the device to the power supply, make sure that the current, voltage and 
frequency match the input voltage, current and frequency specified on the information label on the 
device. 

 

Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the 
required power consumption of the device. 

 

Attention 
General safety
 

 

Do not block the ventilation openings. Without proper heat dissipation and air circulation, the 
internal components may overheat. This can result in product damage. 

 

Do not shake the device. Avoid brute force when installing or operating the device. 

 

If the device is dropped or struck, disconnect the device from the electrical power supply 
immediately. 

 

If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it 
on immediately. Let the device reach room temperature before switching it on, otherwise it may be 
damaged by the formed condensation. 

 

If the device fails to work properly, discontinue the use immediately. 

 

Attention 
For professional use only 
This device shall be used only for the purposes it is designed for. 

This device is designed to be used as a trailing-edge dimmer. Any incorrect use may lead to hazardous 
situations and result in injuries and material damage. 

 

This device is not suitable for households. 

 

This device does not contain user-serviceable parts. Unauthorized modifications to the device will 
render the warranty void. Such modifications may result in injuries and material damage. 

 

Attention 
Before use, examine the device visually for any defects. 

Make sure that: 

 

All screws used for installing the device or parts of the device are tightly fastened and are not 
corroded. 

 

There are no deformations on housings, fixations and installation points. 

 

The power cables are not damaged and do not show any material fatigue. 

 

 

Summary of Contents for 50444

































Reviews: