background image

 

  

 

 

 

 

Ordercode: 935000 

Combo 8, 8” Portable Soundsystem 

IMPORTANT: 

The manufacturer will not accept liability for any resulting damages caused by the non-observance of 
this manual or any unauthorized modification to the system. 
 

 

Always let the device cool down before cleaning or servicing. 

 

Always disconnect power from the mains, when system is not used. Only handle the power cord by 
the plug. Never pull out the plug by tugging the power cord. 

 

Always operate the unit with the AC ground wire connected to the electrical system ground. 

 

Avoid flames and do not put close to flammable liquids or gases. 

 

Avoid ground loops! Always be sure to connect the power amps and the mixing console to the 
same electrical circuit to ensure the same phase! 

 

Before changing the ground, always turn off your amplifier. 

 

Connecting amplifier outputs to oscilloscopes or other test equipment, while the amplifier is in bridge 
mode, may damage both, the amplifier and test equipment. 

 

Do not connect this device to a dimmer pack. 

 

Do not drive the inputs with a signal level higher than required to drive the equipment to full output. 

 

Do not insert objects into air vents. 

 

Do not open the device and do not modify the device. 

 

Do not open this device. Risk: hazardous radiation exposure. 

 

Do not switch the system on and off in short intervals, as this would reduce the system’s life. 

 

Do not put your equipment next to TV, radio, etc., because of interference or distortion. 

 

If the external cable is damaged, it has to be replaced by a qualified technician.

 

If device is dropped or struck, disconnect mains power supply immediately. Have a qualified 
engineer inspect for safety before operating. 

 

If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not 
switch it on immediately. The arising condensation water might damage your system. Leave the 
system switched off until it has reached room temperature. 

 

If you connect other parts of the system, beware ground loops. 

 

If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit securely 
(preferably in the original packing material) and return it to your Dap Audio dealer for service. 

 

In system setup, the amplifier's output power must be 50%-100% higher than the loaded loudspeakers 
rated power. 

 

In typical use, please set the volume to 0dB position. 

 

Make sure that the amplifier is turned down, before turning the power on or off. In this way you can 
avoid supersonic frequencies, which could damage your speakers. 

 

Make sure that the available voltage is not higher than stated on the rear panel. 

 

Make sure that the power cord is never crimped or damaged. Check the device and the power 
cord from time to time. 

 

Make sure that the core diameter of extension cords and power cords is sufficient for the required 
power consumption of the device. 

 

Make sure that the signals coming into the mixer are balanced, otherwise hum could be created. 

 

Make sure you do not use the wrong kind of cables or defective cables. 

 

Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear 

 

Never let the power cord come into contact with other cables! Handle the power cord and all 
connections with the mains with particular caution! 

 

Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord. 

 

Never strain the cable insert or the female part in the device. There must always be sufficient cable 
going to the device. Otherwise, the cable will be damaged, which can cause serious damage. 

 

Never use the device during thunderstorms, unplug the device immediately. 

 

Never leave various parts of the packaging  (plastic bags, polystyrene  foam, nails,  etc.) within 
children’s reach, as they are potential sources of danger. 

 

Never remove warning or informative labels from the unit. 

 

Never use anything to cover the ground contact. 

 

Only use device indoors, avoid contact with water or other liquids. 

 

Please read this manual carefully and keep it for future reference. 

 

Please turn off the power switch, when replacing the power cord, signal cable or selecting the input 
mode switch. 

 

Prevent distortion! Make sure that all components connected to the device have sufficient power 
ratings. Otherwise, distortion will be generated because the components are operated at their limits. 

Summary of Contents for COMBO 8





















Reviews: