background image

Model W1796/W1797 2-Gun Spray Set

-7-

Assembly

2.

  Screw  the  cup  onto  the  top  of  the 

body.

3.

  Attach the air hose to the spray gun 

with a 

1

4

" NPT quick connect fitting 

(not included).

4.

  Attach  the  spray  gun  to  an  air  hose 

regulated between 29 and 50 PSI.

 

Note: 

For the best results, use a hose 

that  will  be  dedicated  for  spray  use 
only. Do not use a hose that has been 
used  with  an  in-line  oiler  or  other 
possible contaminant. 

1.  Fluid  Control: 

Controls  the  volume 

of  material  that  travels  through  the 
fluid tip.

2.  Pattern  Control: 

Adjusts  the  spray 

pattern  from  a  round  pattern  to  a 
wide fan.

3.  Air  Flow  Control: 

Controls  the  fluid 

pressure inside the spray gun.

4.  Atomizing  Cap: 

Controls  the  spray 

pattern from vertical to horizontal.

5.  Trigger: 

Two  stage  trigger.  Stage 

one only releases compressed air for 
blowing off the work piece. Stage two 
sprays material. 

6.  Material  Cup: 

Holds  the  paint  to  be 

sprayed.

7.  Regulator/Gauge:

 

Regulates inlet air 

pressure  to  the  spray  gun.  It  can  be 
attached  directly  to  the  gun  for  on-
the-spot  air  adjustments  or  directly 
from the air source.

 

 
 

Note:

  DO  NOT  attach  to  an  unregu-

lated air source that exceeds 120 PSI.

Figure 4. 

Controls.

 

Controls

Fluid Control

Pattern Control

Atomizing Cap

Trigger

Air Flow Control

Regulator Control

Figure 3. 

Installing filter.

1.

  Insert  the  filter  into  the  gun  body 

(see 

Figure 3

).

Summary of Contents for SHOP FOX W1796

























Reviews: