manualshive.com logo in svg

Shively Labs 6822, Instruction Manual Installation, Operation, & Maintenance, Page: 28 / 78

Share
Download
Shively Labs 6822 Instruction Manual Installation, Operation, & Maintenance Download Page 28

Mounting the Antenna Bay(s)

20

Tower leg or mounting 
pipe 3-1/2 to 6 inches 
outside diameter:

a. At the locations you marked on the mounting pipe (

Set up the mounting 

location.

 on page 1), scrape away any paint or other coating to achieve good 

electrical contact.

NOTE

Mount antenna bays with feed straps up, clear of all guylines and other 

obstructions.

b. Using the threaded rods (

40

), support clamps (

41

), and 5/8-11 galvanized 

hardware (

Figure 16

, 

37

, 

38

, and 

39

), attach the antenna bays at the marked 

locations. Tighten in accordance with 

Table 1

 on page 1.

c. Repeat for the other antenna bay(s) as applicable.
d. Align the bays to the correct azimuth and align them vertically with each 

other, then tighten the mounting hardware in accordance with 

Table 1

 on 

page 1.

e. Repaint the pipe as needed around the antenna bay mount.

Figure 16. Bay mounting on pipe  

3-1/2" - 6" OD

NOTE

The  Model  6822  does  not  require  pressurization  or  purging.  The  feed 

system up to the bay may be pressurized.

Proceed to 

Connecting the Antenna (single-bay)

 on page 21 or 

Connecting the 

Antenna (2- to 6-bay)

 on page 23 as applicable.

Summary of Contents for 6822















































































Reviews:

No comments