background image

Getting

 St

ar

ted

….. 

GB 

IE 

EVERY PRECAUTION IS TAKEN TO ENSURE THAT YOUR BUILDING HAS NO     
ELEMENT  INCORRECTLY PLACED OR POSSIBLY HAZARDOUS, HOWEVER 
PRIOR TO USE PLEASE CHECK ALL  SURFACES FOR THE FOLLOWING: 

(1) 

RAISED GRAIN, SPLINTERS: Sand down timber to smooth finish 

(2) 

NAIL/SCREW/PIN HEADS PROUD: Tap home to be flush with surface of 
timber 

(3) 

DAMAGED SCREW HEADS RESULTING IN SHARP SPLINTERS OF MET-
AL:  Replace 

(4) 

SHARP ENDS OF NAILS/ SCREWS/ PINS PROTRUDING THROUGH THE 
PANEL: Remove and reposition. 

(5) 

 ENSURE ALL PARTS ARE SECURED AGAINST REASONABLE FORCE: 
Remove and refit 

(6) 

 ENSURE THERE ARE NO LOOSE PARTS: Remove and refit/discard 

Important!  

Safety 

IMPORTANT ! 

For your safety please 

read carefully the safety warnings   

Check that you have noted all the following instructions 

 

We advise the use of non slip protective gloves throughout 

the assembly process. 

 

We advise the use of steel capped protective footwear 

throughout the assembly process 

 

We advise the use of protective headwear and safety     

goggles throughout the assembly process   

 

Where a ladder is in use another person must hold the    

ladder. 

 

Do not attempt to work in windy conditions 

 

We advise the use of a scaffold tower when fitting the roof , 

for felting or if you cannot reach from the ground. 

 

Do not allow children near the tools and work area 

 

Follow any safety precautions quoted by the manufacturer 

for any equipment you use  

 

We advise that you use a helper to hold the glass in position 

whilst  you nail the beading in place 

 

Check all parts before assembly 

 

Only use child and animal safe wood preservative 

 

Do not use creosote 

 

Allow the wood preservative to fully dry before use 

 

Regularly check the building for wear and tear 

03

 

Summary of Contents for Casita 2016

























Reviews: