background image

Care, Maintenance and Recycling 

1. 

Pallet and timber widely recycled 

2. 

Cardboard widely recycled 

3. 

Plastic strapping  subject to local regulations  

4. 

Plastic sheeting subject to local regulations.                            

(1) 

Visually check for weather damage. 

(2) 

Check and replace if necessary any Silicone sealant if used on your       
building.   

(3) 

Check the roofing material for wear. 

(4) 

The doors and windows may require periodical adjustment. 

(5) 

Ensure your building is well ventilated especially during hot weather. 

(6) 

During extremely hot periods humidify your building to prevent the timber     
from drying out.                       

The 5 golden rules of care:

 

The 6 golden rules of maintenance:

 

1. 

Timber widely recycled 

2. 

Metal fixings widely recycled 

3. 

Glass widely recycled 

4. 

Roofing felt not currently recycled.                             

packaging

 

Building 

(1) 

Ensure your base is level and firm. 

(2) 

Ensure the building is not sitting directly on the ground using damp proof 
membrane or the optional timber base. 

(3) 

Ensure every piece of timber and surface, especially that is hidden upon  
assembly is treated with a top quality wood preservative at least twice 
(before assembly). Turn the panels upside down whilst painting so the    
treatment runs into the seams.  

(4) 

Garden buildings are not waterproof, therefore we recommend you seal   
between all the panels with a silicone based sealant. 

(5) 

Regularly check your roofing felt for weather damage and leaks. 

Getting

 St

ar

ted

….. 

GB 

IE 

05

 

Recycling and disposal:

 

Summary of Contents for 10x10 Sun Pent

























Reviews: