background image

BACK PANEL

BACK PANEL

CONNECTING THE HARDWARE

Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls present.

Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning properly in
all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.

If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to the 
carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher fi rst and then 
plug the adaptor into a functional AC outlet.

6

1. DC POWER INLET: 

The switcher is fi tted with a DC power plug input connector. 
Please ensure that the plug used is of an approved type and is 
of suffi cient current carrying capacity with the correct voltage and 
connector polarity. 12Volt DC power supply 2A Max.

2. IR EXTENDER CONTROL: 

Support one of IR Extender (IR input) Extend distance maximum 
984 ft. (300 m)

Note: DO NOT install or remove any connections while the 
power is ON.

3. RS-232 CONNECTION: 

RS-232 control port to allow for interfacing to a PC, such as a 
computer or touch panel control, to the switcher via this DB-9pin 
Female connector for serial RS-232 control.  

4. INPUTS-1~4 VGA-AUDIO SOURCE PORTS: 

Connect 4x inputs of VGA-STEREO AUDIO signals from 4x VGA-
Stereo Audio source devices switch to 8x VGA Monitor displays.

5. OUTPUTS-1~8 VGA-AUDIO PORTS:

Connect 8x VGA-Stereo Audio signal via 4x VGA & Stereo Audio 
cable output to VGA Monitor displays and Audio devices switch 
from 4x VGA-Audio input source devices.

Power Jack:

DC Jack - Inner OD Ø 2.1 mm (+)
                Outside OD Ø 5.5mm (GND)
Power input -12VDC, 2A

IR Extender Jack:

 Female Jack - inner OD Ø 3.5mm

Remote port:

 DB-9pin Female connector

VGA-Audio Via 1x HD-15p connector, 1x 3.5mm 
P-Jack

Note: With 1x female D-Sub connector. Female 
Jack - inner OD Ø 3.5 mm

VGA-Audio Via 1x HD-15p connector, 1x 3.5mm 
P-Jack

Note: With 1x female D-Sub connector. Female 
Jack - inner OD Ø 3.5 mm

Summary of Contents for SB-4148LCM

















Reviews: