Shinko SOVC-48CN1-RC7C Technical Manual Download Page 46

Page: 46 / 68

SHINKO-4/5 ton High Efficiency A5 Duct Technical Manual

Trial Run

The trial run must be carried out after the entire installation has been completed. Please confirm the

following points before the trial run:

✓

The indoor unit and outdoor unit are installed properly.

✓

Piping and wiring are correctly completed.

✓

The drainage is unimpeded.

✓

The ground wiring is connected correctly.

✓

The lengths of the piping and the amount of recharged refrigerant have been recorded.

✓

The power voltage fits the rated voltage of the air conditioner.

✓

There is no obstacle at the air outlet and inlet of the indoor and outdoor units.

✓

Check whether all valves are opened.

✓

Pre-heated the air conditioner by power on.

Trouble shooting



Out

door unit

’s malfunction and protection codes

Content

LED1

LED2

LED3

Power supply phase sequence error

Flashing

Extinguished

Lack of Phase A, B of power supply

Lack of Phase C of power supply

Extinguished

Low pressure protection

Flashing

Extinguished

Over-current protection of compressor

Extinguished

Flashing

High pressure protection

Extinguished

Flashing

Extinguished

Discharge temperature protection

Summary of Contents for SOVC-48CN1-RC7C





































































Search results

Summary of Contents for SOVC-48CN1-RC7C

Reviews:

Shinko SOVC-48CN1-RC7C, Technical Manual, Page: 46 / 68

Search results

Summary of Contents for SOVC-48CN1-RC7C

Reviews: