Shinco SDP6820 Service Manual Download Page 3

SAFTY NOTICE

Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000    per volt or more sensitivity.
Connect a 1500    10W resistor,paralleled by a 0.15uF
150V AC capacitor between a knomn good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).

SAFTY PRECAUTIONS

LEAKAGE CURRENT CHECK

Measure the AC voltage across the 1500    resistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3V.A reading
exceeding 0.3V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO PLAYER
power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.

READING SHOULD NOT EXCEED 0.3V

DVD VIDEO PLAYER

AC OUTLET

AC VOLTMETER

Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check

0.15uF 150V AC

1500
10W

(5000    per volt
or more sensitivity)

Good earth ground
such as a water pipe,
conduit, etc.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

Summary of Contents for SDP6820












Reviews: