127
8. Install the port block sub-assembly as follows:
●
Install the check and relief valve assemblies (26)
and springs (31) in the port block (3) and tighten
the plugs (29) to 63.7 N·m.
●
Install the high pressure relief valve check port’s
plug (56) tighten to 29.4 N·m.
●
Press in the oil seal (17) to 3mm depth from the
surface in the port block (3) and secure with snap
ring (42).
●
Install the needle bearings (20) in the port block
with the marking surface to outside, and protrude
2.5 mm from the matching surface.
●
If removed, install the dowel pins on the housing.
●
Apply the grease to the spring and install it in the
housing.
●
Install the gasket (47) on the housing.
●
Apply the grease to the valve plates (9 and 10) and
low pressure relief valve (32) for prevent fall down
and install them to the port block.
●
The notch side (V shape ditch) of the pump valve
plate (10), to against the cylinder block assembly.
●
The brass color surface of the motor valve plate (9)
to against the cylinder block assembly.
●
Apply the mission oil to the cylinder block contact
surfaces and install the port block assembly (3) to
the housing and tighten the bolts to 49.0 ± 5 N·m.
9. Install the trunnion cover to the housing as follows:
●
Install the slide metal (24) and position the pin hole
against the port block direction in the swash plate
sub assembly (6).
●
Install the bearing (16) in the trunnion cover (57).
●
Install the washer (18) in the trunnion cover.
●
Install the oil seal (66) in the housing to 1 mm
depth from the cover surface.
●
Install the trunnion shaft (15) in the cover and
secure with snap ring (44).
●
Install the trunnion cover sub-assembly with align
the slide metal’s hole to trunnion shaft’s pin, and
tighten the screw to 6.9±0.7 N·m.
10. Install the charge pump as follows:
●
Install the O-Ring and pins to the port block.
●
Install the plate (87) with the brass color surface to
against the charge pump.
●
Position the pin (34) into the input shaft (7), and
install the trochoid rotor sub-assembly (25), on the
input shaft with align the punch marks (1) and pin
center (2).
●
Install the new oil seal in the charge pump case and
secure with snap ring.
●
Install the charge pump case sub assembly (4) with
align the pins, and tighten the bolts to 49.0 ± 5
N·m.
11. Inspect the both shafts (7 and 8) are rotated smoothly
by adjustable wrench after assembled.
418X
3. Port Block
42. Snap Ring
17. Oil seal
20. Needle Bearing
419X
420X
Downloaded from
www.Manualslib.com
manuals search engine
Summary of Contents for CM284
