![Sherwood Scuba SAGE Manual Download Page 58](http://html1.mh-extra.com/html/sherwood-scuba/sage/sage_manual_1256682058.webp)
58
SAGE MANUAL
© Pelagic, 2017
Doc. No. 12-7864-r06 (8/21/17)
UPLOADING/DOWNLOADING
As previously described (page 34), the Sage can be paired using the Bluetooth® feature. This requires a PC, Mac, or mobile device running Diver-
log software and equipped with Bluetooth® functionality. If your personal computer is not equipped with internal Bluetooth® hardware, a Blue-
tooth® dongle can be purchased separately from a computer store.
Alternately, The Sage is configured with a 4 pin data connection port located on the back of the case. It can be used with the included adapter clip
to connect the Sage with a PC or Mac using a USB cable. Connect the adapter clip to the Sage. When connecting the adapter clip to the Sage,
ensure that the 4 ports on the clip are properly fitted over the 4 pins on the Sage. Then connect the USB interface cable to the adapter. The Sage
and USB cable assembly can now be connected to a PC or Mac running Diverlog software.
NOTE: If a USB cable is connected to the Sage, Bluetooth® connection will be blocked or disabled. Though any active downloads, uploads, or
firmware updates using Bluetooth® will be allowed to finish first.
DATA PORT
USB ADAPTER
ADAPTER INSTALLED
4 pins
CARE AND CLEANING
Protect your Sage from shock, excessive temperatures, exposure to chemicals, and tampering. Protect the lens against scratches with the stick on
Sage lens protector. Small scratches will naturally disappear underwater.
• Soak and rinse the Sage in fresh water at the end of each day of diving, and check to ensure that the areas around the PC interface data port,
and buttons are free of debris or obstructions.
• To dissolve salt crystals, use lukewarm water or a slightly acidic bath (50% white vinegar/50% fresh water). After removal from the bath, place
the Sage under gently running fresh water. Towel dry before storing.
• Keep your Sage cool, dry, and protected during transport.
data port
INSPECTIONS AND SERVICE
Your Sage should be inspected annually
by an Authorized Sherwood Dealer who will perform a factory prescribed function check and inspection for
damage or wear. To keep the 2 year limited warranty in effect, this inspection must be completed one year after purchase (+/- 30 days).
Sherwood recommends that you continue to have an inspection performed every year to ensure it is working properly. The costs of annual inspec-
tions are not covered under the terms of the 2 year limited warranty.
To Obtain Service:
Take your Sage system to an Authorized Sherwood Dealer.
ALTITUDE SENSING AND ADJUSTMENT
Prior to the first dive of a series of repetitive dives, Altitude (i.e., ambient pressure) is measured upon activation and every 15 minutes until a dive is
made or operation reverts to Watch Mode.
• While it is operating in Surface Mode after a dive, measurements are taken every 15 minutes during the 24 hour period after surfacing.
• Measurements are only taken when the unit is dry.
• Two readings are taken, the second reading 5 seconds after the first. The readings must be within 1 foot (30 cm) of each other to record that
ambient pressure as the current altitude.
• No adjustments are made during any time that the wet contacts are bridged.
When diving in high altitude waters from 3,001 to 14,000 feet (916 to 4,270 meters), the Sage automatically adjusts to these conditions providing
corrected depth, and reduced No Decompression and O2 Times at intervals of 1,000 feet (305 meters).
At an elevation of 3,001 feet (916 meters), Depth calibration automatically changes from feet of seawater to feet of fresh water. This is the first ad-
justment to the algorithm. When the Conservative Factor feature is set to ON, No Decompression Times are calculated based upon the next higher
3,000 feet (915 mete) altitude. All adjustments for altitudes greater than 11,000 feet (3,355 meters) are then made to allowable dive times for
14,000 feet (4,270 meters). At Sea Level, calculations are based upon an altitude of 6,000 feet (1828.8 meters).
The Sage will not function as a dive computer above 14,000 feet (4,270 meters).
Summary of Contents for SAGE
