SHERCO 2015 450 SEF-R Workshop Manual Download Page 42

Page: 42 / 76

450 SEF-R

❱❘

Cleaning the throttle body

•  Clean the throttle body by means of a carbure-
tor cleaner spray (Net Carbu).
•  Be sure to clean the edge of the throttle valve
on each side with the throttle fully opened.
•  Clean the injector. Blow.

❱❘

Installing the throttle body

Reassemble the parts following the reverse order of
that of the removal, put

special connector

grease

inside the connections (power injector, GST, etc.).
•

If you remove the inlet sleeve, pay attention

to the direction!

• Adjust the clearance of the throttle cable.

• Disconnect the computer connector. Visually
inspect the connectors.
• Clean with carburetor or universal cleaner.
• Blow.

• Apply

special connector

grease.

• Reconnect.

Cleaning the throttle body

Summary of Contents for 2015 450 SEF-R













































































Search results

Summary of Contents for 2015 450 SEF-R

Reviews:

Related manuals for 2015 450 SEF-R

Brands by name

Popular brands

SHERCO 2015 450 SEF-R, Workshop Manual

Search results

Summary of Contents for 2015 450 SEF-R

Reviews:

Related manuals for 2015 450 SEF-R

Brands by name

Popular brands