ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 91

Page: 91 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Table 5.12 Set the parameters of the Leap Motion function

Items

Description

Speed

The velocity percentage of the Dobot Magician:

Unit: %

Value range: 1 - 100

Default value: 50

Scale

The scale of the Dobot Magician:

Unit: %

Value range: 1 - 100

Default value: 100

High performance/Low
performance

Choose a performance mode suitable for your computer. Select the Low
performance (default) for the low configuration computer to prevent
video delay



NOTE

Move your hand in the workspace of the Leap Motion controller to control the Dobot

Magician to perform a particular task, as shown in Table 5.13.

Table 5.13

The robotic arm’s movement created with your hand gesture

Hand gesture

Robotic arm’s movement

Move your palm up, down, front,
back, right, or left

The robotic arm moves accordingly

Clench your fist

Control the air pump to suck air

Unclench your fist

Turn off the air pump

Controlling with your Mouse

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands