ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 75

Page: 75 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Figure 5.69 Adjust the laser focus



The point marked by a red box, as shown in Figure 5.70, corresponds to the position

of the end-effector of the Dobot Magician. This point changes its position only within

the annular area when the robotic arm moves.

Figure 5.70 The point corresponding to the end-effector of the robotic arm

Once this step is complete, the next time you start to engrave, directly import a PLT

or SVG image file without adjusting the position of the laser kit, and click

SyncPos

and then click

Start

to start engraving on the paper, as shown in Figure 5.71.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands