ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 72

Page: 72 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Figure 5.63 Input text



Click

Open

to import an image file such as BMP, JEPG, or PNG to convert this image to

its corresponding SVG file that the DobotStudio supports.ssss Once this image is imported,

the

SVG Converter

dialog box is displayed, as shown in Figure 5.64. In this dialog box,

drag the slider to set the black and white threshold, and click

Convert Bitmap To SVG

perform the conversion, and then click

Plot to Main Scene

to display the converted SVG

file on the annular area of the

Write & Draw

page.

Figure 5.64 Convert Bitmap to SVG



NOTE

We recommend to set the Velocity in the range of 0mm/s to 500mm/s and to adjust the

acceleration between 0mm/s

and 500mm/s

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands