ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 48

Page: 48 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Jogging the Dobot Magician in the Cartesian or Joint coordinate system to move

the robotic arm to the end position C as needed.

Click

+Point

to save the coordinates corresponding to the positions B and C, as

shown in Figure 5.19.

Figure 5.19 Save the second position B and the end position C

Set the percentage of both speed and acceleration for playback, for example 50.

Set

Loop

Click

Start

. The Dobot Magicin perfrom the sequence of ARC trajectory as taught

from its memory system, moving from positions A to C .

Teaching & Playback Example

Application Scenarios

You can use Teaching & Playback function module to manipulate the Dobot Magician to

accomplish different tasks such as transportation or intelligent sort. This topic introduces how to

move small cubes from position A to B in the

JUMP

motion mode.

Prerequisites



The Dobot Magician has been powered on and connected to your computer.



A suction cup kit has been installed. For details, see

5.2.1 Installing a Suction Cup Kit

Procedure

Figure 5.20 Choose SuctionCup as the end-effector

The

Teaching & Playback

page is displayed.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands