manualshive.com logo in svg

ShenZhen Yuejiang Technology Dobot Magician, User Manual, Page: 38 / 153

Share
Download
ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 38

                   

 

  Dobot Magician User Guide

 

Dobot Magician Homing Operation

 

Issue V1.9.0 (2020-07-23) 

User Guide 

Copyright © Yuejiang Technology Co., Ltd. 

 

33 

 

Items 

Description 

Leap Motion 

Set the parameters such as speed, scale, and performance for hand gesture 
control. 

Mouse 

Set the parameters such as speed, scale, and performance for mouse control. 

LaserEngraving 

Set the parameters such as junction velocity, linear acceleration, acceleration, 
pen down position, and DPI for laser engraving. 

 

 

Common Areas of DobotStudio Page 

The  DobotStudio  offers  the  following  common  areas  shared  by  all  the  function  modules  to 

control the robotic arm. 

 

You  can  select  the  liner  rail  or  an  end-effector  on  the  DobotStudio  page,  as  shown  in 

Figure 5.3. 

 

Figure 5.3    The linear rail and end-effector drop-down list 

 

Table 5.3    The linear rail and end-effector drop-down list 

Items 

Description 

Linear rail 

When the robotic arm is connected to a linear rail, click this item to enable the rail 

End-effector   

drop-down list 

When the end-effector is a suction cup kit, gripper kit, laser kit or writing and drawing 
kit, select the corresponding kit in this list 

 

 

You can also perform other operations on the DobotStudio page such as Setting, Home, 

Emergency Stop, and viewing the versions, as shown in Figure 5.4. 

 

Figure 5.4    Setting, Home, Emergency Stop, and viewing the versions 

 

Table 5.4    Setting, Home, Emergency Stop, and viewing the versions 

Items 

Description 

Setting 

Set the robotic arm such as firmware upgrade, sensor and base setup. For details, please 
refer to Table 5.2 

Home 

Set the Dobot Magician back to its home position to get a correct reference position 

When the Dobot Magician is moving, if its movement is hindered by an obstacle or the 
stepper motors lost steps, perform the homing operation 

Emergency Stop 

Stop the robotic arm if an emergency occurs 

Summary of Contents for Dobot Magician


























































































































































Reviews:

No comments