ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 116

Page: 116 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

111

After burning 3D printing firmware, if the LED indicator on the base turns red, it

indicates that the connection of the 3D printing kit is abnormal.

WARNING

Please DO NOT operate or turn off Dobot Magician when burning firmware, to avoid

machine damage.

5.9.3.2

Performing 3D Printing

Procedure

Select

Machine > settings

on the Cura page.

The

Machine settings

page is displayed.

Set the corresponding parameters on the Machine settings and click

, as

shown in Figure 5.133. Table 5.16 lists the values of the parameters that need to

be set. The other parameters are set by default.

Figure 5.133 Parameters setting

Table 5.16 3D printing parameters description

Parameter

Description

Maximum width

The maximum width

please set to 80mm

Maximum depth

The maximum with

please set to 80mm

Maximum height

The maximum height

Please set to 150mm

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands