ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 115

Page: 115 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

110

Operating Cura

If you need to use Cura software for 3D printing, please launch the Cura software after burning

firmware.

Prerequisites



Slice software

Cura

has been installed.

The download path is

https://ultimaker.com/en/products/ultimaker-cura-software/list

Please download the recommended version

V14.07

. The way how to install and use is not

descripted in this topic.



The 3D printing model has been prepared.



The printing platform has been prepared and please place it in the workspace of Dobot

Magician.



Dobot Magician has been powered on.



Dobot Magician has been connected to DobotStudio successfully (Only USB connection

is supported).



The 3D printing kit has been installed.

5.9.3.1

Burning Firmware

Procedure

The

3D Printing FM

page is displayed, as shown in Figure 5.132.

Figure 5.132 Burn firmware

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands