background image

 

7 | 

P a g e

 

 

GRAPHIC SYMBOLS 

The oven is provided with multiple graphic symbols on the control panel and adjacent to the power 
inlet. The symbols identify hazards and the functions of the adjustable components, as well as 
important notes in the user manual. 

Symbol 

Definition 

 

Indicates that you should consult your service manual for further instructions.  

Indique que l'opérateur doit consulter le manuel d'utilisation pour y trouver les instructions 
complémentaires.   

 

 

Indicates Temperature  

Repère température  

 

 

Indicates the Over Temperature Limit system 

Indique le système de dépassement de temperature 

 

Indicates AC Power  

 Repère le courant alternative 

 

Indicates I/ON and O/OFF 
I repère de la position MARCHE de l'interrupteur d'alimentation 
O repère de la position ARRÊT de l'interrupteur d'alimentation 

 

 

Indicates protective earth ground 

Repère terre électrique 

 

 

Indicates UP and DOWN respectively 

Touches de déplacements respectifs vers le HAUT et le BA 

 

 

 
Indicates a Manually Adjustable control 
Indique un bouton réglable manuellement 

 

 

Indicates a Potential Shock Hazard  

Signale danger électrique 

 

 

 

WEEE Directive compliant logo 

 

Indicates the unit should be recycled (Not disposed of in land-fill) 

 

        

Indiq

ue l’appareil doit être recyclé (Ne pas jeter dans une décharge) 

 

Summary of Contents for FX14-2



























Reviews: