7
USAGE:
Fill the kettle with the desired amount of water.
NOTE:
Always make sure to fill the water between the minimum and maximum marking of the
level indicator.
1.
Place the filled kettle on the base and plug the appliance into the wall outlet.
NOTE: If the temperature is set and you wish to change it, you will have to turn off the
kettle and switch it back on.
2.
Plug the kettle into power source. The default settings are: Boil to 212°F / No Keep Warm / 3 Second
Extended Boil. Refer to Default Settings Diagram on right. Press (Start) button. While the water starts
to heat up, (Heat Water) will be flashing. The LCD panel will show 212°F.
3.
Once the water is boiled, (Heat Water) will stop flashing. Next the kettle will go into the Extended
Boil for 3 seconds, will briefly flash indicating the Extended Boil is in progress. Once that is done,
the LCD panel will show 212°F with (Heat Water) in display. The water is boiled and ready for use.
4.
If you do not wish to use the default settings, change the settings before you press (Start)
button.
NOTE:
You have to keep the Heat water temperature at 212°F in order for water to boil.
Refer to Keep Warm, Extended Boil and Heat Water Diagrams on right.
SETTING KEEP WARM:
Press (Function) button, the (Keep Warm) will come on and
display will show 000°F. Use (Arrow) buttons to change the temperature (110°F - 190°F).
The Keep Warm will be activated for 30 minutes. You will hear kettle go on and off to try to maintain
the desired temperature.
NOTE:
If Keep Warm set temperature can't be reached within 30 minutes
after the water has been boiled/heated up, then Keep Warm setting won't function.
If you do not wish to use the Keep Warm function, set it as 000.
SETTING EXTENDED BOIL:
Press the (Function) button again and (Extended Boil) will
come on and display will show 003. Use (Arrow) buttons to set Extended boil (3-20 seconds).
NOTE:
The Extended Boil function will be effective only if the desired temperature is set to 212°F.
After selecting the desired settings, press (Start) button.
SETTING HEAT WATER:
Use Arrow buttons to select the desired temperature
(110°F -212°F). You may increase or decrease the temperature in increments of 10°F.
USAGE
(Refer to p. 6 for Parts Identification)
FILTER USAGE/CLEANING KETTLE
8
IF THE KETTLE BOILS DRY
All users of this appliance must read and understand the User’s Manual before operating this appliance.
If the kettle is operated properly, it is unlikely that the kettle will boil dry. The kettle is equipped with a special safety device that will
automatically turn the kettle off if it boils dry. The kettle will remain off until it is refilled with a minimum amount of water required
for operation. If the kettle does boil dry, turn the unit off and unplug it. Let it cool down for 30 minutes before using it again.
KEEP WARM
HEAT WATER
L
DEFAULT SETTINGS
FILTER USAGE/CLEANING
In order to help reduce the amount of scale residue, the kettle
is equipped with a special mesh filter (located inside the spout).
When you start to notice deposits left on the filter, it is time to
clean your filter.
IMPORTANT: Make sure the kettle is removed from the
base and is unplugged before cleaning it. Always wait
until the unit cools down completely.
1. Empty the kettle.
2. Hold the top part of the filter with index finger and thumb
and pull upwards. You may have to hold the kettle while
removing the filter. Be careful not to press on the mesh as
that may damage the filter.
3. To clean the filter, rinse under tap water while brushing it gently with a soft bristle brush.
4. When done, place the filter back into the spout and gently push it in until you hear a click.
5. Rinse out kettle with fresh water. In order to reduce scale build-up, empty out any left over
water after boiling.
1. Make sure the kettle is removed from the base and is unplugged before cleaning it. Always wait until the unit cools down completely.
WARNING: Do not immerse plug, cord or housing into water or any other liquid due to the risk of electric shock. Do not use
abrasive cleansers to clean the inside or outside of the kettle or base. Do not place kettle or base into the dishwasher.
2. Clean the outside of the kettle with a soft damp cloth.
3. With continuous use, mineral deposits that are found in regular tap water may leave scale deposits on the inside of the
kettle. To remove the build-up, fill the kettle with a white vinegar/water solution (mix 3 cups of each). Let it sit overnight.
4. Empty the vinegar/water solution. Wipe the inside of the kettle with a damp cloth.
5. Fill the kettle with clean water. Boil the water, then discard. Repeat. Now your kettle is ready for use.
CLEANING YOUR KETTLE
REMOVING
FILTER
CORRECT FILTER POSITION
L
EXTENDED BOIL
