Sharp XG-C45XU Quick Start Reference Sheet Download Page 2

Projector Driver Application Note

Sharp XG-C45XU

Revision A

DR-SHP22 - 12/18/03

SP Controls reserves the right to modify specifications without notice at any time.

This document describes the 

SmartPanel

 Projector Driver for the 

Sharp XG-C45XU 

projector. For

information on configuring and using the Panel see the 

SmartPanel Configuration and Installation Guide.

Please read the 

SPECIAL CONTROL NOTE

 in the 

Control Wiring

 section of this document before

attempting control of the projector. This note describes how the Sharp’s 

Economy Mode 

impacts the

projector’s behavior.

I. PROJECTOR CONTROL

A.   Volume and Power Control

Volume control on the Sharp is 

absolute

.  Absolute volume control is also possible with SP Controls’

option 

Audio Follow Video Preamplifer 

(SP3-AFVP+).

B.   Input Selection Mapping

The following table specifies the factory-preset input mapping for this Driver. The 

Configuration Utility

can be used to customize these settings your installation.

Selection 1:

VIDEO

Selection 2:

S-VIDEO

Selection 3:

RGB 1

Selection 4:

RGB 2

Input choices available for the Sharp with this
Driver are VIDEO, S-VIDEO, RGB 1, and RGB 2.

C.   Hidden Function Mapping

The following table specifies the factory preset hidden function mapping for this Driver. The

Configuration Utility

 can be used to customize these settings your installation.

Selection 1:

BLACK SCREEN

Selection 2:

ENTER

Selection 3:

ADJUST LEFT

Selection 4:

ADJUST RIGHT

Off:

MENU

Volume Up:

ADJUST UP

Volume Down:

ADJUST DOWN

Hidden functions names are based on the Sharp remote and controls on top of the projector.  Hidden
functions are accessed by pressing the indicated key while the holding the 

On 

key down.

ADJUST

 controls, 

ENTER 

and 

UNDO 

navigate through onscreen menus. 

UNDO 

is a “return to previous

menu” or “back” command. 

MENU

 can also be used as 

UNDO.   

The area zoomed with the 

ENLARGE

function can be moved using the 

ADJUST

 keys.

BLACK SCREEN 

is a toggle

.

Projector

Ready

Warm-up

OFF

ON

Volume

VIDEO

S-VIDEO

RGB 1

RGB 2

Projector

Ready

Warm-up

OFF

ON

Volume

ADJUST

 UP

ADJUST

 DOWN

MENU

BLACK

SCREEN

ENTER

ADJUST

LEFT

ADJUST

 RIGHT

Summary of Contents for XG-C45XU






Reviews: