Sharp XE-A177 Full Detailed Instruction Manual Download Page 18

Page: 18 / 134

Selecting an Operating Mode

When you turn the register on and press the

key, the mode selection window will appear on the display,

listing available operating modes as shown below.

Mode selection window

Operating Modes

You can select any mode other than REG from the list in the mode selection window. Your register supports
the following operating modes:

REG mode

This mode allows you to enter various sales information. The mode selection

window does not list this mode. To select this mode from the mode selection

window, press the

key.

OPXZ mode

This mode allows clerks to take X or Z reports on their sales information.

OFF mode

This mode locks all the operations of the register. When you select this mode, the

window will disappear. Pressing any key turns the register ON.

VOID mode:

This mode allows correction after finalizing a transaction.

X1/Z1 mode

This mode is used to take various daily total reports (X1/Z1 reports).

X2/Z2 mode

This mode is used to take various weekly or monthly reports (X2/Z2 reports).

PGM mode

This mode is used to program various items.

SD CARD mode

This mode allows you to save and load the data of your register to and from an SD

card.

Summary of Contents for XE-A177







































































































































Search results

Summary of Contents for XE-A177

Reviews:

Related manuals for XE-A177

Brands by name

Popular brands

Sharp XE-A177, Full Detailed Instruction Manual

Search results

Summary of Contents for XE-A177

Reviews:

Related manuals for XE-A177

Brands by name

Popular brands