Sharp vc-ga56z Service Manual Download | Manualshive

Page: 7 / 74

background image

7

VC-GA56Z
VC-GH96Z

2-3 CARES WHEN REASSEMBLING

INSTALLING THE CASSETTE HOUSING
When the cassette housing is installed on the mechanism,
the initial setting is essential condition.
There are two initial setting methods, namely electrical
and mechanical.
1. Electrical initial setting
So as to perform initial setting of mechanism execute the
Step 1 of Installation of cassette housing. After ascertain-
ing the return to the initial setting position (*1) install the

cassette housing. (Conditions: When mechanism and
PWB have been installed)

2. Mechanical initial setting
Feed the pulley feed gear of loading motor with screw
driver. After ascertaining the return to the initial set posi-
tion (*1) install the cassette housing in the specified
position. (This method is applied only for the mechanism.)

INSTALLING THE MECHANISM ON PWB
Lower vertically the mechanism, paying attention to the
mechanism edge, and install the mechanism with due
care so that the parts are not damaged. So as to fix the
mechanism to the main PWB install two housings. (Fit the
antenna cover to one of them. For other, fix the vicinity of
loading motor and solder joint side of main PWB.) Con-
nect again the FFC cable (AA-MH, AD-ME, AH-MH)
between the mechanism and the main PWB.

PARTS WHICH NEED PARTICULAR CARE
When installing the mechanism chassis on the PWB unit,
take care so as to prevent deformation due to contact of
mechanism chassis with REC TIP SW.

Pulley feed gear

Screwdriver

Tilt mark (*1)

Casecon
drive gear

Drive angle of
cassette housing

VC-GH96Z

REC TIP SW

END SENSOR

AE CONNECTOR

AC CONNECTOR

AL CONNECTOR

START SENSOR

«
...
5
6
7
8
9
...
»

Summary of Contents for vc-ga56z











































































Reviews:

No comments

Related manuals for vc-ga56z

DLR-2104/1.0TBV

Brand: Eneo Pages: 90

Brand: Q-See Pages: 13

Brand: Q-See Pages: 5

Brand: Hunt Electronic Pages: 57

Brand: COP Security Pages: 28

INSPIRE WHITE series

Brand: COP Security Pages: 36

Brand: COP-USA Pages: 66

Brand: COP-USA Pages: 114

Digital Video Recorder

Brand: COP-USA Pages: 130

Brand: Euro Video Pages: 76

EVD-16/400A16MN

Brand: Euro Video Pages: 94

Brand: RTimes Pages: 21

Brand: Seg Pages: 32

Brand: Velleman Pages: 20

Brand: Alien Hero Pages: 156

Brand: Home electric Pages: 68

Brand: Idis Pages: 27

Brand: Idis Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands