13
14
0800 862 0453
www.sharkclean.eu
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can build up and
impact the performance of your steam mop
over time. To extend the life of your product we
recommend that you use distilled water.
CARE OF YOUR CLEANING PADS
1
We recommend washing your cleaning pads
separately from other fabrics to avoid picking up
lint. For optimal cleaning performance, the pads
may need to be washed up to (3) three times. Only
use liquid detergent (no powder detergent). Do not
use any fabric softeners or bleach. Line dry. Do not
tumble dry.
(fig. 16)
2
If there are loose threads on the cleaning pads,
carefully cut the thread with scissors. Do not pull on
them or cut at the base.
(fig. 17)
IMPORTANT:
The cleaning pads may be very hot
from the steam. Use caution when removing. Let the
unit cool for 2-3 minutes.
fig. 17
CLEANING THE NOZZLE
NOTE:
To prevent clogging, it is recommended that
you periodically clean the Direct Steam Nozzle and
the extension hose stem.
1
Your Handheld Steamer should not normally require
cleaning, however, should you notice a decrease in
the steam output, it may be necessary to remove
mineral deposits built up around the nozzles.
2
Unplug the cleaner from the electrical outlet.
3
Use a small diameter stiff metal wire, such as a
straightened metal paperclip, and carefully insert the
end of the wire into the nozzle orifice. See illustration
above.
(fig. 18)
4
Move the wire back and forth several times to remove
any deposits.
5
Plug in the appliance to the power outlet and test
steam output.
fig. 18
fig. 16
40°
Troubleshooting Guide
PROBLEM
POSSIBLE REASONS & SOLUTIONS
The Shark
®
Multi-Function
Steam Mop Lite will not
turn-on.
Your steam mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
The unit will not make steam.
Is there water in the water tank? If not, add water to your steam mop following
instructions on page 4.
When using the unit in the handheld mode, ensure that you are holding the
handheld unit horizontally to optimize the steam output. Do not hold the
handheld unit vertically as this will impede steam production. Use the hose with
your chosen accessory to reach difficult areas and above floor cleaning whilst
maintaining the horizontal position of the handheld unit.
If the unit still does not make steam, follow the instructions on page 13 to clean
the nozzle.
The Shark
®
Multi-Function
Steam Mop Lite leaves water
on the floor.
Check to see if your cleaning pad is too wet. We recommend you unplug the
steam mop and change the cleaning pad.
Make sure the cleaning pad is attached correctly.
The Shark
®
Multi-Function
Steam Mop Lite left a white
spot on the floor.
Do not leave your steam mop on the floor with a damp or wet cleaning pad.
If you’re using tap water, we recommend switching to distilled water.
Make sure the cap is securely on the water tank.
Floors are cloudy, streaky or
spotty after steaming.
The cleaning pad might be dirty. Change the cleaning pad.
If you washed the cleaning pad with powder detergent, then your pad could be
damaged and require replacement. Replacement pads are available at
www.sharkclean.eu.
This could also be an indication of prior soap or grease residue that has
accumulated on the floor. As our steam mops use only a small amount of
water, it may not be wet enough to rinse off the accumulation that the steam
is bringing to the surface. We suggest rinsing the floor with nothing but water,
letting it dry, and then steam mopping again with a clean pad. One or more
rinses generally removes the residue.
A more stubborn case may require you to rinse the floor with a mix of one part
vinegar and two parts water.
The Shark
®
Multi-Function
Steam Mop Lite is hard to
push.
Make sure the cleaning pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. If so, replace the cleaning
pad.
Care of Your Steam Mop- cont.
Summary of Contents for S7000UK
Page 1: ...S7000UK OWNER S GUIDE ...
