Sharp R-9H58, Service Manual

Page: 30 / 44

R-9H58
28
3. Disconnect wire lead from the turntable motor.
4. Remove the two (2) screws holding the turntable motor
to the mounting plate of the oven cavity bottom.
5. Pull the turntable coupling out of the oven cavity.
6. Turntable coupling and motor will be free.
1. CARRY OUT 3D CHECKS.
2. Disconnect wire leads from the convection motor.
Remove the convection fan belt and pulley(M).
3. Remove two (2) screws holding the convection motor
mounting angle to the heater duct and base cabinet.
CONVECTION MOTOR REMOVAL
1. CARRY OUT 3D CHECKS.
2. Remove cooling fan motor and magnetron refer to
“Cooling Fan Motor Removal” and “Magnetrom
Removal”.
3. Disconnect wire leads from damper motor and damper
switch.
4. Remove two(2) ovenside screws holding damper motor
DAMPER ASSEMBLY REMOVAL
REMOVAL
1. CARRY OUT 3D CHECKS.
2. Disconnect the wire leads from the fan motor and
thermal cut-out.
3. Remove the three (3) screws holding the chassis
support to rear cabinet, control panel back plate and
waveguide.
4 Remove one (1) tab holding the fan duct to air guide .
5. Remove the fan motor assembly from the oven cavity.
6. Remove the fan blade assembly from the fan motor
shaft according the following procedure.
1) Hold the edge of the rotor of the fan motor by using a
pair of grove joint pliers.
CAUTION:
*
Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor.
Because the rotor is easy to be shaven by pliers
and metal pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not transform the bracket by touching with the
pliers.
2) Remove the fan blade assembly from the shaft of the
fan motor by pulling fan retainer clip and rotating the fan
blade with your hand.
3) Now, the fan blade will be free.
CAUTION:
*
Do not use this removed fan blade again.Because
the hole(for shaft) of it may become bigger than a
standard one.
FAN MOTOR REPLACEMENT
7. Remove the two (2) screws and nuts holding the fan
motor and thermal cut-out mounting angle from the fun
duct.
8. Now, the fan motor is free.
INSTALLATION
1. Install the fan motor and thermal cut-out angle to the
fan duct with the two (2) screws and nuts.
2. Install the fan blade assembly to the fan motor shaft
according the following procedure.
1) Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
2) Apply the screw lock tight into the hole(for shaft) of the
fan blade.
3) Install the fan blade assemby to the shaft of fan motor
by pushing the fan blade with a small, light weight, ball
peen hammer or rubber mallet.
CAUTION:
*
Do not hit the fan blade strongly when installed
because the bracket may be transformed.
* Make sure that the fan blade rotates smooth after
installed.
* Make sure that the axis of the shaft is not slanted.
3. Install the fan duct to the air guide.
4. Install the chassis support to the oven cavity with three
(3) screws.
5. Connect the wire leads to the fan motor and the thermal
cut-out, referring to the pictorial diagram.
4. Take out the convection motor assembly from the unit.
The convection motor assembly is now free.
5. Remove two (2) screws and nuts holding the motor to
mounting angle.
6. Convection motor is now free.
angle to thermal protection plate (right).
5. Damper assembly is free.
6. Remove one (1) screw holding damper motor to damper
motor angle and one (1) screw holding damper switch
to damper motor angle.
7. Damper motor and switch are free.
Rear view
Coil
Gap
Rotor Bracket
Stator
Groove joint pliers
Shaft
Axis
Stator
These are the position
where should be
pinched with pliers
Rotor
Side view
Shaft
Table
Center of
bracket