Sharp R-890SLM Service Manual Download Page 26

Page: 26 / 47

R-890SLM

11 - 4

[9] POSITIVE LOCK CONNECTOR REMOVAL

1. CARRY OUT 3D CHECKS.
2. Push the lever of positive lock

connector.

3. Pull down on the positive lock

connector.

Figure C-2. Positive lock

connector

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

CONNECTORS TO THE TERMINALS, CONNECT

THE POSITIVE LOCK

SO THAT THE LEVER

FACES YOU.

[10] OVEN LAMP REMOVAL

1. CARRY OUT 3D CHECKS.
2. Remove the wire leads as Positive lock

connector removal

above.

3. Lift up the oven lamp from its retaining clips.
Now, the oven lamp is free.

[11] POWER SUPPLY CORD REPLACEMENT

1. REMOVAL

1. CARRY OUT 3D CHECKS.
2. Remove the one (1) screw holding the green/yellow wire to

the cavity back plate.

3. Disconnect the leads of the power supply cord from the

noise ﬁlter, referring to the Figure C-3(a).

4. Release the power supply cord from the rear cabinet.
5. Now, the power supply cord is free.

Figure C-3 (a) Power Supply Cord Replacement

Power supply cord

Green/ Yellow-

wire

Brown wire

Oven cavity back plate

Blue wire

Noise filter

Screw

F 8 A

[12] TOP HEATING ELEMENTS REMOVAL

1. CARRY OUT 3D CHECKS.
2. Remove the two (2) screws holding the two (2) terminals of

the main wire harness to the top heating element.

3. Remove the two (2) screws holding the two (2) grill heater

angles to the top of the oven cavity.

Terminal

Push

Pull down

Lever

Positive lock¨

connector

Figure C-2. Positive lock, connector

Bulb

Socket

Oven lamp

Lock

2. REINSTALLATION

1. Insert the moulding cord stopper of power supply cord into

the square hole of the cavity back plate, referring to the

Figure C-3(b).

2. Install the earth wire lead of power supply cord to the oven

cavity with one (1) screw and tight the screw.

3. Connect the brown and blue wire leads of power supply cord

to the noise ﬁlter correctly, referring to the Pictorial Diagram.

Figure C-3(b). Power Supply Cord Replacement

POWER

SUPPLY CORD

MOULDING

CORD STOPPER

OVEN CAVITY

BACK PLATE

SQUARE HOLE

4. Remove the two (2) grill heater angles from the oven cavity.
5. Remove the top heating element from the top of the oven

cavity.

6. Now the top heating element is free.

Service_R-890SLM.indd 26

4/25/09 10:55:46 AM

Summary of Contents for R-890SLM
















































Search results

Summary of Contents for R-890SLM

Reviews:

Related manuals for R-890SLM

Brands by name

Popular brands

Sharp R-890SLM, Service Manual

Search results

Summary of Contents for R-890SLM

Reviews:

Related manuals for R-890SLM

Brands by name

Popular brands