background image

27

R-405DK

6. Re-install choke cover  to door panel by pushing.

Note:

After any service to the door;

(A) Make sure that door sensing switch and secondary

interlock switch are operating properly. (Refer to
chapter “Test Procedures”.).

(B) An approved microwave survey meter should be

used to assure compliance with proper microwave
radiation emission limitation standards.

After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through

latch holes and that latch head goes through center of
latch hole.

2. Deviation of door alignment from horizontal line of cavity

face plate is to be less than 1.0mm.

3. Door is positioned with its face pressed toward cavity

face plate.

4. Check for microwave leakage around door with an

approved microwave survey meter.  (Refer to Microwave
Measurement Procedure.)

Note:

The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be air-
tight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity.

Figure C-5. Door Replacement

SEALER FILM

Installation
1. Put the adhesive tape on the backing film of the sealer

film as shown in Fig. C-6.

2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel

Figure C-6. Sealer film

Summary of Contents for R-405DK









































Reviews: