Sharp R-21LCF - Oven Microwave 1000 W Service Manual Download Page 24

Page: 24 / 40

R21LCF

11 – 3

Figure C-1. Oven lamp socket

[8] POSITIVE LOCK CONNECTOR (NO-CASE TYPE) REMOVAL

1. Disconnect the power supply cord, and remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Push the lever of positive lock

connector.

5. Pull down on the positive lock

connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

CONNEC-

TORS TO THE TERMINALS, NSTALL THE POSITIVE
LOCK

SO THAT THE LEVER FACES YOU.

Figure C-1. Positive Lock

Connector

[9] ANTENNA MOTOR REMOVAL

1. Disconnect the power supply cord.

2. Remove the one (1) screw holding the base plate cover to the base

plate and remove the base plate cover.

3. Disconnect the wire leads from the antenna motor and remove the

one (1) screw holding the antenna motor.

4. Remove the antenna motor shaft from the antenna motor.

5. Now, the antenna motor is free.

[10] COOLING FAN MOTOR REMOVAL

1. REMOVAL

1. Disconnect the power supply cord and remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from the fan motor.

5. Remove the one (1) screw holding the capacitor holder to the oven

cavity rear plate.

6. Remove the one (1) screw holding the fan duct to the oven cavity

rear plate.

7. Release the tabs of the capacitor holder from fan duct.

8. Remove the fan duct from the oven.

9. Remove the fan blade from the fan motor shaft according to the fol-

lowing procedure.

10.Hold the edge of the rotor of the fan motor by using a pair of groove

joint pliers.

CAUTION: MAKE SURE THAT ANY PIECES DO NOT ENTER THE

GAP BETWEEN THE ROTOR AND THE STATOR OF THE
FAN MOTOR. BECAUSE THE ROTOR IS EASY TO BE
SHAVEN BY PLIERS AND METAL PIECES MAY BE PRO-
DUCED.

DO NOT TOUCH THE PLIERS TO THE COIL OF THE
FAN MOTOR BECAUSE THE COIL MAY BE CUT OR
INJURED.

DO NOT DISFIGURE THE BRACKET BY TOUCHING
WITH THE PLIERS.

11.Remove the fan blade assembly from the shaft of the fan motor by

pulling and rotating the fan blade with your hand.

12.Now, the fan blade will be free.

CAUTION: DO NOT RE-USE THE REMOVED FAN BLADE

BECAUSE THE HOLE (FOR SHAFT) MAY BE LARGER
THAN NORMAL.

13.Remove the two (2) screws holding the fan motor to the fan duct.

14.Now, the fan motor is free.

2. INSTALLATION

1. Install the fan motor to the fan duct with the two (2) screws.

2. Install the fan blade to the fan motor shaft according to the following

procedure.

3. Hold the center of the bracket which supports the shaft of the fan

motor on the flat table.

4. Install the fan blade to the shaft of fan motor by pushing the fan

blade with a small, light weight, ball peen hammer or rubber mallet.

CAUTION: DO not hit the fan blade hard when installing because the

bracket may be disfigured.

MAKE SURE THAT THE FAN BLADE ROTATES
SMOOTH AFTER INSTALLED.

MAKE SURE THAT THE AXIS OF THE SHAFT IS NOT
SLANTED.

5. Install the fan duct to the oven cavity rear plate with the one (1)

screw.

6. Insert the tabs of the capacitor holder to the fan duct.

7. Install the capacitor holder to the oven cavity rear plate with the one

(1) screw.

8. Re-connect the wire leads to the fan motor.

Terminal

Push

Pull down

Lever

Positive lock

connector

Summary of Contents for R-21LCF - Oven Microwave 1000 W









































Search results

Summary of Contents for R-21LCF - Oven Microwave 1000 W

Reviews:

Related manuals for R-21LCF - Oven Microwave 1000 W

Brands by name

Popular brands

Sharp R-21LCF - Oven Microwave 1000 W, Service Manual

Search results

Summary of Contents for R-21LCF - Oven Microwave 1000 W

Reviews:

Related manuals for R-21LCF - Oven Microwave 1000 W

Brands by name

Popular brands