background image

8

R-209BW

DESCRIPTION OF LSI

The I/O signal of the LSI are detailed in the following table.

Pin No.

Signal

I/O

Description

1

RESET

IN

Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is supplied. Temporarily
set to “L” level the moment power is supplied, at this time the LSI is reset. Thereafter
set at “H” level.

2

TEST

IN

Connected to GND.

3

VSS

IN

Power source voltage: -5V.
VSS voltage of power source circuit input. Connected to VC.

4

OCS3

IN

Internal clock oscillation frequency setting input.
The internal clock frequency is set by inserting the resistor oscillation circuit with
respect to OCS4 terminal.

5

OCS4

OUT

Internal clock oscillation frequency control output.
Output to control oscillation input of OCS3.

6

VD1

IN

Power source for oscillation circuit.

7

VDD

IN

Power source voltage input terminal.
Connected to GND.

8

AVDD

IN

A/D converter power source voltage.
The power source voltage to drive the A/D converter in the LSI. Connected to GND.

9

AVREF

IN

A/D converter power source voltage.
The power source voltage to drive the A/D converter in the LSI. Connected to GND.

10

AVSS

IN

Power source voltage: -5V.
AVSS voltage of power source circuit input. Connected to VC.

11-13

P40-P42

IN

Terminal to change functions according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the
Model in operation is applied to set up its function.

14

P43

IN

To input signal which communicates the door open/close information to LSI.
Door close “H” level signal (0V).  Door open “L” level (-5V).

15

BZ

OUT

Signal to sound buzzer (2.0 kHz).

A: key touch sound.

B: Completion sound.

16

R00

OUT

Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G6 line keys on key matrix is touched.

17

R01

OUT

Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G5 line keys on key matrix is touched.

18

R02

OUT

Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G4 line keys on key matrix is touched.

19

R03

OUT

Key strobe signal.
SigM nal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G3 line keys on key matrix is touched.

20

P20

OUT

Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G2 line keys on key matrix is touched.

21

P21

OUT

Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P23, K00, K01 and K02
terminal while one of G1 line keys on key matrix is touched.

22

P22

OUT

Terminal not used.

A

B

0.1 sec.

2.0 sec.

H : GND

L : -5V

H : GND

L : -5V

Summary of Contents for R-209BW

















Reviews: