background image

R-209BW

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
FOREWORD AND WARNING ............................................................................................................................... 2
PRODUCT DESCRIPTION .................................................................................................................................... 3
TEST PROCEDURE .............................................................................................................................................. 5
TOUCH CONTROL PANEL ASSEBLY ................................................................................................................. 7
CONTROL PANEL CIRCUIT ............................................................................................................................... 10
PARTS LIST ........................................................................................................................................................ 11
PACKING AND ACCESSORIES ......................................................................................................................... 12

S6013R209BPW/

MICROWAVE OVEN

MODEL

R-209BW

In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens con-
tain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier
Assembly,  High Voltage Harness etc..)

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

SUPPLEMENTAL SERVICE MANUAL

This is a supplemental Service Manual for Model R-209BW. This model is quite similar to base
model R-209BK. Use this supplemental manual together with the Base Model Service Manual
(Refer No. is S1803R220BPW/) for complete operation, service information, etc..

DEFROST

EXPRESS

MINUTE

PLUS

SNACKS

COOKING

REHEATING

POPCORN

BEVERAGE

BAKED

FRESH

POTATO

VEGETABLES

DINNER

PLATE

ROLL,

MUFFIN

Summary of Contents for R-209BW

















Reviews: