Sharp Notevision XG-NV7XU Service Manual Download Page 15

Page: 15 / 110

XG-NV7XU

2. Removing the Top and Front Cabinets

2-1. Remove the two screws from the top and bottom cabinets.
2-2. Remove the three screws from the top and front cabinets.
2-3. Slowly lift the back of the top cabinet and disconnect the operation key unit connector (KY) and the speaker

connector (SP). Pull up and off the top cabinet.

2-4. Remove the two screws from the front cabinet and disconnect the remote control unit connector (RC). Unhook

the center of the front cabinet and take out the front cabinet.

(SC)

(RC)

(SP)

(KY)

(SP(P301))

2-4

2-3

R/C Unit

Front Cabinet

Operation Key Unit

Top Cabinet

Bottom Cabinet

2-1

2-2

Summary of Contents for Notevision XG-NV7XU















































































































Search results

Summary of Contents for Notevision XG-NV7XU

Reviews:

Related manuals for Notevision XG-NV7XU

Brands by name

Popular brands

Sharp Notevision XG-NV7XU, Service Manual

Search results

Summary of Contents for Notevision XG-NV7XU

Reviews:

Related manuals for Notevision XG-NV7XU

Brands by name

Popular brands