Sharp MX 3070 Troubleshooting Manual Download Page 22

Page: 22 / 56

General Problems

I DON'T KNOW HOW TO ADJUST THE TIME THE

MACHINE ENTERS ENERGY SAVE MODE

Check

Solution

Set the time the machine enters
energy save mode in the Energy Save
settings of setting mode.

■

Set the time the machine enters energy save mode in the Energy Save settings
of setting mode.

Set the time the machine enters Preheat Mode.



"Setting mode (administrator)"

→

[System Settings]

→

[Energy Save]

→

[Eco Setting]

→

[Preheat Mode Setting]

Set the time that Auto Power Shut-Off takes place



"Setting mode (administrator)"

→

[System Settings]

→

[Energy Save]

→

[Eco Setting]

→

[Auto Power Shut-Off]

→

[Auto Power Shut-Off Timer]

I FORGOT THE ADMINISTRATOR PASSWORD

Check

Solution

Was the administrator password
changed from the factory default
setting?

■

Contact your dealer or nearest SHARP Service Department.

For the factory default administrator password, see "TO THE ADMINISTRATOR
OF THE MACHINE" in Start Guide. After changing the password, take special
care to remember it.

I DON'T KNOW WHOM TO CONTACT FOR

MAINTENANCE AND SERVICE

Check

Solution

Please check the customer support
information.

■

The customer support information can be found on the following page.

Summary of Contents for MX 3070

























































Search results

Summary of Contents for MX 3070

Reviews:

Related manuals for MX 3070

Brands by name

Popular brands

Sharp MX 3070, Troubleshooting Manual

Search results

Summary of Contents for MX 3070

Reviews:

Related manuals for MX 3070

Brands by name

Popular brands