Sharp MX 3070 Troubleshooting Manual Download Page 13

Page: 13 / 56

General Problems

THE PAPER MISFEEDS

Check

Solution

Is a torn piece of paper remaining in
the machine?

■

Follow the instructions in the touch panel to remove all paper.

Is too much paper loaded in the tray?

■

Make sure that the stack of paper in the tray is not higher than the indicator line.

►

Placing the original and adding paper (page 5)

Are multiple sheets feeding at once?

■

Fan the paper well before loading it.

Are you using paper that is not within
the specifications?

■

Use SHARP-recommended paper.

Using paper that is for other models or special paper that is not supported may
result in misfeeds, creases, or smudges.



- "SUPPLIES" in Start Guide

For paper that is prohibited or not recommended, see User's Manual.

Has the paper in the tray absorbed
moisture?

■

Use the heater switch.

When using the machine in a cold location or a humid location, we recommend
that you switch on the heater switch on the machine.

►

Power and connector positions (page 4)

If you will not be using paper in a tray for a long time, remove the paper from the
tray and store it in a bag in a dark and dry location.

Are the bypass tray guides adjusted
to the width of the paper?

■

Adjust the bypass tray guides to the width of the paper.

►

Placing the original and adding paper (page 5)

Is the bypass tray extension guide
pulled out?

■

When loading large-size paper, pull out the extension guide.

►

Placing the original and adding paper (page 5)

Is the bypass feed roller dirty?

■

Clean the surface of the bypass feed roller.

►

Maintenance (page 6)

Is 5-1/2" x 8-1/2" (A5) size paper
loaded?

■

When loading 5-1/2" x 8-1/2" (A5) size paper, place the paper in the horizontal
(5-1/2" x 8-1/2"R (A5R)) orientation.

Is the paper size specified?

■

If you are using a non-standard size, be sure to specify the paper size.

If the size of paper loaded into a tray was changed, be sure to check the paper
size setting.



"Setting mode"

→

[System Settings]

→

[Common Settings]

→

[Paper Settings]

→

[Tray Settings/ Paper Settings]

→

[Paper Tray Settings]

→

[Tray Registration]

Did you add paper to the bypass tray?

■

When adding paper, remove any paper remaining in the bypass tray, combine it
with the paper to be added, and reload as a single stack.

If paper is added without removing the remaining paper, a misfeed may result.

Summary of Contents for MX 3070

























































Search results

Summary of Contents for MX 3070

Reviews:

Related manuals for MX 3070

Brands by name

Popular brands

Sharp MX 3070, Troubleshooting Manual

Search results

Summary of Contents for MX 3070

Reviews:

Related manuals for MX 3070

Brands by name

Popular brands