background image

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 13

(4)

Copy/Printer color balance and density adjustment 
(Automatic adjustment)

When  a  printer  option  is  installed,  be  sure  to  execute  the  above
item.

1)

Enter the SIM46-74 mode.

2)

Press [EXECUTE] key.

The  high  density  process  control  is  performed,  and  the  copy
color patch image (adjustment pattern) is printed out. 
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)

3)

Set the color patch image (adjustment pattern) paper printed in
procedure 2) on the document table.

Set  the  color  patch  image  (adjustment  pattern)  printed  in  the
procedure  2)  on  the  document  table.  Place  the  color  patch
image  so  that  the  fine  lines  are  on  the  left  side.  At  that  time,
place 5 sheets of white paper on the printed color patch image
(adjustment pattern).

4)

Select [FACTORY] target, and press [EXECUTE] key.

When the color balance is customized by the manual color bal-
ance adjustment (SIM 46-21) according to the user's request,
and the color balance is registered with SIM63-7 as the service
target, if the color balance is required to be adjusted, select the
[SERVICE] target.

The  copy color balance  adjustment  is automatically executed
and prints the color balance check patch image.

If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.

5)

Press [EXECUTE] key.

The  printer  color  patch  image  (adjustment  pattern)  is  printed
out.  (A4/11"  x  8.5"  or  A3/11"  x  17"  paper  is  automatically
selected.)

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

(1*,1($872$'-8670(176(59,&(

(;(&87(

35(66>(;(&87(@72352&21(;(&87,21$1'35,177+(7(673$7&+

3/($6(86(63(&,),('7<3(2)$$25;;6,=(3$3(5

)257+,6$'-8670(17

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

(1*,1($872$'-8670(176(59,&(

(;(&87(

352&21(;(&87,1*

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

(1*,1($872$'-8670(176(59,&(

3/($6(6(/(&77+(02'()$&725<256(59,&($1'3/$&(

7+(35,17('7(673$7&+21'2&80(17*/$667+(135(66>(;(&87(@

/,*+7$5($$7/()76,'(21'2&80(17*/$66

(;(&87(

6(59,&(

)$&725<

Q

O P

N

M

L

K

J

I

H

G

F

E

D

C

B

A

Y

M

C

Bk

High
density

Low
density

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

(1*,1($872$'-8670(176(59,&(

&21),507+($'-3$7&+$1'35(66>(;(&87(@72$'-2)5(*,675$7,21(;(

$1'35,177+(7(673$7&+

3/($6(86(63(&,),('7<3(2)$25h6,=(3$3(5

)257+,6$'-8670(17

(;(&87(

Summary of Contents for MX-2314N




















Reviews: