![background image](http://html.mh-extra.com/html/sharp/lc32dv24u-31-5-lcd-tv/lc32dv24u-31-5-lcd-tv_service-manual_373863026.webp)
ELECTRICAL ADJUSTMENTS
D-1
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
On-Screen Display Adjustment
1.
2.
Set the VOLUME to minimum.
Press the VOL. DOWN button on the set and the
channel button (9) on the remote control for more than
2 seconds to display adjustment mode on the screen as
shown in Fig. 1-1.
Fig. 1-1
3.
4.
5.
6.
7.
8.
9.
Use the CH. UP/DOWN button or Channel button (0-9)
on the remote control to select the options shown in
Fig. 1-2.
Press the SETUP/TV MENU button on the remote control
to end the adjustments.
To display the adjustment screen for TV, AV,
COMPONENT, HDMI and PC mode, press the INPUT
button on the remote control.
To display the adjustment screen for DVD mode, press
the TV/DVD button on the remote control.
Receive the DIGITAL broadcasting.
To display the adjustment screen for DTV mode, select
the digital channel.
Press the VOL.DOWN button on the set and the channel
(9) on the remote control for more than 2 seconds.
•
•
•
Use an isolation transformer when performing any
service on this chassis.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor with a heat sink,
apply silicon grease on the contact section of the heat
sink. Before applying new silicon grease, remove all the
old silicon grease. (Old grease may cause damages to
the IC and Transistor).
2. BASIC ADJUSTMENTS
Prepare the following measurement tools for electrical
adjustments.
1. Pattern Generator
03 R DRIVE (N)
8
TV
S.Strech
480i
Function
Step No.
2-1: WHITE BALANCE
1.
2.
3.
4.
5.
6.
7.
8.
Place the set in Aging Test for more than 15 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Press the INPUT button on the remote control to set to
the AV mode.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-2 and
press the channel button (03) on the remote control to
select "R DRIVE(N)".
Press the CH. UP/DOWN button on the remote control
to select the "R DRIVE (N)", "R CUTOFF (N)",
"B DRIVE (N)", "B CUTOFF (N)", "R DRIVE (C)",
"R CUTOFF (C)", "B DRIVE (C)", "B CUTOFF (C)",
"R DRIVE (W)","R CUTOFF (W), "B DRIVE (W)" or
"B CUTOFF(W)".
Adjust the LEFT/RIGHT button on the remote control
to whiten the R DRIVE (N), R CUTOFF (N),
B DRIVE (N), B CUTOFF (N), R DRIVE (C),
R CUTOFF (C), B DRIVE (C), B CUTOFF (C),
R DRIVE (W) ,R CUTOFF (W), B DRIVE (W) and
B CUTOFF(W) at each step tone sections equally.
Perform the above adjustments 6 and 7 until the white
color is achieved.
FUNCTION
R DRIVE(N)
R CUTOFF(N)
G DRIVE(N)
G CUTOFF(N)
B DRIVE(N)
B CUTOFF(N)
R DRIVE(C)
R CUTOFF(C)
G DRIVE(C)
G CUTOFF(C)
B DRIVE(C)
B CUTOFF(C)
R DRIVE(W)
R CUTOFF(W)
G DRIVE(W)
G CUTOFF(W)
B DRIVE(W)
B CUTOFF(W)
BAK LIGHT CENT
BAK LIGHT MAX
NO.
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
29
30
NO.
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
50
FUNCTION
BAK LIGHT MIN
BRIGHTNESS CENT
BRIGHTNESS MAX
BRIGHTNESS MIN
TINT
SHARP H1 MAX
SHARP H1 MIN
SHARP H2 MAX
SHARP H2 MIN
SHARP V1 MAX
SHARP V1 MIN
CONTRAST CENTER
CONTRAST MAX
CONTRAST MIN
COLOR CENTER
COLOR MAX
COLOR MIN
CONTRAST 40
Fig. 1-2