14
LC-32LE240
LC-40LE240
Operation Manual (Continued)
English
- 12 -
Connecting to a DVD Player
via Component Sockets
(YPbPr) or Scart Cable
Some DVD players are connected through
•
COMPONENT SOCKETS (YPbPr)
. In this case,
you must use the supplied Component video
connection cable for enabling connection. First,
plug single jack of the cable to the TV’s YPbPr
socket (side). Afterwards, insert your component
cable’s (not supplied) connectors into the
socket
part of the Component video connection cable (see
illustration below). Colours of the connected jacks
should match.
To enable audio connection, use the
•
VGA/Component
Audio cable
. First, plug single jack of the cable
to the TV. Afterwards, insert your DVD player ’s
audio cable’s connectors into the
socket
part of the
VGA/Component audio connection cable
(
see
illustration below
). Colours of the connected jacks
should match.
YPbPr
Side view
DVD Player
Connection Cable
(supplied)
YPbPr Video Cable
(Not supplied)
When the connection is made, switch to
•
YPbPr
source. See,
Input selection
section.
Note:
To connect YPb Pr device, you should use supplied
component (YPbPr) connection cable
You may also connect through the
•
SCART
input.
SPDIF
SCART
VGA
Coax.OUT
1
2
Scart
Cable
(not
supplied)
External device
Note
•
: These three methods of connection perform the
same function but in different levels of quality. It is not
necessary to connect by all three methods.
Recordings of HD programmes can occupy bigger
•
size on the USB disk depending on the broadcast’s
resolution. For this reason it is recommended
to use USB hard disk drives for recording HD
programmes.
Do not plug out the USB/HDD during the recording.
•
This may harm the connected USB/HDD.
Multipartiton support is available. Maximum two
•
different partitions are supported. If the disk have
more than two partitions, crash may occur . First
partition of the usb disk is used for PVR ready
features. It also must be formatted as primary
partition to be used for PVR ready features.
Some stream packets may not be recorded because
•
of signal problems, so sometimes video may freezes
during playback.
Record, Play, Pause, Display (for PlayListDialog)
•
keys could not be used when teletext is ON. If a
recording starts from timer when teletext is ON,
teletext is automatically turned of f. Also teletext
usage is disabled when there is ongoing recording
or playback.
• Radio record is not supported.
• The TV can record programmes up to ten hours.
Connecting to a DVD Player via HDMI
Please refer to your DVD player’s instruction book
for additional information. Power off both the TV and
the device before making any connections.
Note
: Not all cables shown in the illustration are
supplied.
If your DVD player has an
•
HDMI
socket, you can
connect via
HDMI
for better video and audio quality.
SPDIF
SCART
VGA
Coax.OUT
1
2
External device
(not
supplied)
HDMI Cable
When you connect to DVD player as illustrated above,
•
switch to the connected
HDMI
source. See,
Input
Selection
section for more information on changing
sources.
A01_MB62_[GB]_1910UK_IDTV_TC_PVR_NICKEL17_32942LED_ROCKER_ZIGGO_10075804_50201074.indd 12
15.03.2012 16:58:32
Summary of Contents for LC-32LE240E
