![Sharp LC-32DH57E-BK Service Manual Download Page 27](http://html.mh-extra.com/html/sharp/lc-32dh57e-bk/lc-32dh57e-bk_service-manual_1254363027.webp)
LC
-
32DH57E-BK/RU-BK/S-BK
4 – 1
LC-32DH57E-BK
Service Manual
CHAPTER 4.
TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE
No power supplied (Front LED does not light up). No power-up even if turned on (Front LED light up)
YES
Is the power cord connector, AC-IN harness, and PD harness
connected to the POWER unit normally?
NO
Reconnect the power cord, the AC-IN harness and PD harness cor-
rectly.
YES
Is the connection of B to B connector between the POWER
unit and the INVERTER unit normal? (P7201-CN7302)
NO
Correct connection or the short circuit of a B to B connector nor-
mally. (P7201-CN7302)
YES
Are F7001 (3.15A) and F7002 (3.15A) normal?
NO
Replace F7001 or F7002 and switch on the power again.
If Fuse still blow out, check L7001, L7002, D7104, VA7001, and
VA7002.
YES
Is DC310V supplied to the primary side capacitor C7114 and
C7108, when the power switch is turned on?
NO
Check whether there are any abnormalities in a rectification circuit.
(D7104, C7114, C7108, L7101)
YES
Is UR12.5V supplied from pin (13) (14) of PD connector
(P7202), when the power switch is turned on?
YES
(*1) fly to the check item of INV60V.
NO
Is about DC400V supplied to primary side capacitor C7112?
NO
Check whether there are any abnormalities in a power factor
improvement circuit. (IC7101, Q7103, D7113, D7213)
YES
Check whether the PS_ON “H” signal is inputted to the pin (6)
of PD connector (P7202) in the power supply unit.
NO
Check whether the PS_ON “H” signal is outputted to pin (10) of PD
connector (P9601) and pin (AC11) of IC3303 (VCT) in the MAIN unit.
YES
Check again after remove parts which have trouble or a short
circuit. Is UR12.5V supplied from pin (13) (14) of PD connec-
tor (P7202)?
NO
Is there a part which breaks down on the UR12.5V line or short-cir-
culated?
YES
YES
NO
Check the power control circuit of UR12.5V.
(IC7201, T7206, D7217, C7220, C7222, C7228, D7215)
Check again after remove parts which have trouble or a short circuit.
After the power supply is turned on, is INV60V generated in
connector P7201 (20-23) pin? (*1)
NO
Is connector CN7302 of the INV unit removed, and is INV60V gener-
ated in connector P7201 (20-23) pin?
YES
YES
NO
Check the inverter power circuit of INV60V.
(D7227, C7221, C7223, T7206, D7220, D7221)
It is failure inside an INV unit. check broken parts or a shorting part.
(Q7809, Q7807, Q7811, Q7810, etc.)
Is BU3.3V/D3.3V supplied to pin (5) (6) of RA connector
(P3301) in a main unit, and pin (1) (2) of P101 in the R/C unit?
NO
Check the power supply circuit of BU3.3V and D3.3V.
(IC9605, IC9607/IC9602, etc.)
YES
“No power supplied (Front LED does not light up)”. “No
power-up even if turned on (Front LED light up).” Is it OK?
NO
Review the former step and check it again.