background image

When using electrical appliances, basic safety precautions should always be followed, including the following.
1.   Read all instructions.
2.  Do not touch hot surfaces. Use handles or knobs.
3.  Keep the rice cooker out of the children’s reach, especially when cooking rice.
4.  Unplug from wall outlet when not in use and before cleaning. Allow to cool before putting on or taking off
 parts.
5.  Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions or has been
 

damaged in any manner.

6.  Use of accessory attachments no recommended by SHARP may cause injuries.
7.  Do not use outdoors.
8.  Extreme caution must be used when moving an appliance containing hot food, water or other hot liquids.
9.  Do not use the appliance for other than intended use.
10. Always unplug and let the rice cooker cool down before cleaning.
11. Do not let cord hang over edge of table or counter or touch hot surfaces.

IMPORTANT SAFEGUARDS

1.  Be sure to remove the sheet of protective paper located between the inner pot and heater plate
 

before using the rice cooking.

2.  Avoid using the rice cooker, if the power supply cord becomes hot. Should this happen, have a qualified

 

electrician check the rice cooker.

3.  Use on a flat, stable surface.

4.  Use the inner pot only in the rice cooker; never on the range top or in the microwave oven.
5.  Do not turn the rice cooker on without both rice and water in the inner pot. Avoid using the rice cooker to
 

heat just water.

PRECAUTIONS

5

1.   Place of use

 

  Do not use the cooker on a wet floor, under direct sunlight or near the gas table.

 

  Do not use the rice cooker within 1 m of TV or radio to prevent the interference.

 

  While cooking, do not put the rice cooker on or near combustible materials such as curtains or vinyl 

   carpets.

2.  How to handle before use

 

  Do not disassemble or repair the cooker by yourself. It may cause trouble such as a fire or electric 

 

  shock. Consult your nearest dealer.

 

  The electrical requirements are a 220V 50Hz, a.c. only protected electrical supply.

 

  It is recommended that a separate circuit serving only this appliance be provided.

 

  To protect against electrical shock, do not immerse the set in water or sprinkling water on the heater plate.

 

  Do not allow children to operate.

 

  Move the rice cooker by handle only. 

 

 

  Never carry it by using of the inner pot holders projecting on both sides of the closed cooker.

 

  Use the plastic spoon provided as accessory.

 

  For porridge use a plastic or wooden deep plastic spoon available on the market.

 

  Never share an electric wall outlet with other appliances.

 

  Never connect the plug with your wet hand as it may be dangerous from electric leakage.

 

  Disconnect the plug from the wall outlet when you do not use the rice cooker.

 

  In case the power cord is broken, it must be replaced by manufacturer or appointed service providers

 

  or equivalent professionals to avoid any damages.

 

  In case the power cord is broken, it must be replaced by manufacture or appointed service providers or

 

  equivalent professionals to avoid any damages.

CAUTIONS FOR USE

Summary of Contents for KS-COM18




























Reviews: