background image

WARNING

 

To reduce the risk of electric shock, discon-

nect from power supply before cleaning.

Aluminum  mesh  filters:

 Clean frequently using hot 

water and a mild detergent. Filters are dishwasher safe.

Charcoal  filters  (additional  filters  for  non-
ducted installations):

 Clean filter surfaces frequently 

with a damp cloth and a mild detergent. DO NOT immerse 

filters in water or put in dishwasher. The special “Clean 

Sense” feature indicates when the filter is to be replaced. 

The blue and yellow stripes will blend to green when it is 

time to change the filter. The “Clean Sense” feature works 

best when facing toward the cooking surface.

To  clean  hood:

 Remove filters. Use a damp cloth and 

a mild detergent to wipe all grease-laden surfaces. Do not 

use abrasive cloth, steel wool pads or scouring powder on 

the Teflon

®

-coated bottom cover or on any painted surface. 

Use care when cleaning blower wheel - it must not become 

bent or misaligned. DO NOT ALLOW WATER TO ENTER 

MOTOR. Make sure all surfaces are completely dry before 

re-installing filters and restoring power. Motor is permanently 

lubricated. Do not oil or disassemble motor.

Teflon

®

 is a registered trademark of DuPont.

11

CLEANING

Summary of Contents for Insight KB-0333K













Reviews: