background image

CHAPTER 7. DATA BLOCK FORMAT

1. Basic format

        Start code : This code may not be provided.

Null is impermissible.

        End code : This code may not be provided.

Null or any same code as the start code is
not permissible.

When master reset is performed, the default is assumed:

    Start 

code 

02h

    End 

code 

0Dh

  Block consecutive No. : This number starts with 30h and cycles

like this: 30h, 31h — 39h, 30h, 31h (Ring
counter system)

  Check sum

: 2 bytes hex number 

Low-order 8-bit data of the complement of
2 for the sum of text data.

  RAM data:

: Even number of data that is obtained by

dividing one byte of RAM data into high-
order 4 bits and low-order 4 bits and con-
verting them to ASCII codes shown in the
code conversion table.

Code conversion table .

Print code (high-order or low-order 4 bits)

Line image

Bit image

Hexadecimal

ASCII

0000

0

30h

0001

1

31h

0010

2

32h

0011

3

33h

0100

4

34h

0101

5

35h

0110

6

36h

0111

7

37h

1000

8

38h

1001

9

39h

1010

A

41h

1011

B

42h

1100

C

43h

1101

D

44h

1110

E

45h

1111

F

46h

CHAPTER 8.  ONLINE application

1. ONLINE preset

1) SRV programming: NONE

2) PGM programming

Job#

PGM-MODE programming for online operation

2690

The assignment of RS232 channel by each devices.

6110

Programming of the terminal number

6111

Programming of the modem control

6112

Programming of the transmission data rate (Bau rate)

6113

Programming of the start and end code.

6115

Programming of time out value

6110

Online Preset reading

[JOB#2690] MRS = 0000

The assignment of RS232 channel by each devices.

X: 1

A:

On-line

2690-A

No

0

Yes (Channel No. = 8)

8

[JOB#6110] MRS = 000001

Programming of the terminal number

NK: Terminal No. = 0 to 999999

1) ID-ENQ :

10bytes

ENQ code (05h)

Terminal No. 000001-999999 (6 bytes)

EOT is set as dummy cahracters. (3 bytes)

2) ACK :

1 byte   06h

3) NAK :

1 byte   15h

4) EOT :

1 byte   04h

5) ENQ :

1 byte   05h

6) TEXT :

Data ASCII (max. 250 bytes)

Block consecutive No.

Start code

End code

Check sum

Example

Memory image

Line image

02

5A

F0

1

2

3

30h

32h

35h

41h

46h

30h

Transmission sequence

1

2

3

2690

X

X

X

ABCD

ST

TL

0

6110

NK

0

x

TL

– 14 –

Summary of Contents for ER-A457








Reviews: