background image

PARTS LIST

No.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

1

AE

N

D

Battery cover

2

AD

N

C

Screw

(for BATTERY COVER)

3

AE

N

D

Manual (ENGLISH)

[except LN0]

AE

N

D

Manual (GERMAN)

[LN0, LM4]

AE

N

D

Manual (FRENCH)

[U1C,LM4, LD0 ]

AE

N

D

Manual (SPANISH)

[U1C, LM4]

AE

N

D

Manual (ITALIAN)

[LN0, LM4]

AE

N

D

Manual (CHINESE)

[LD0, LO0]

AE

N

D

Manual (ARABIC)

[LD0, LO0]

4

AE

N

D

Chinese label

[LD0]

Battery Replacement

Battery used

Type

Model

Quantity

Lithium battery

CR2025

1

Improper replacement of the battery may change or lose the
memory contents.

Be sure to write down any important information stored in the
memory before replacing the battery.

1. Precautions

Since improper use of the batteries may cause leakage or explosion,
strictly observe the following instructions.

Insert the battery with positive side (+) correctly facing up.

Never throw battery into a fire because it might explode.

Keep battery out of reach of children.

Because the battery in the Organizer was installed at the factory, it may

become depleted before the specified expiration time is reached.

2. Battery Replacement

If the display becomes dim and difficult to read, immediately replace the
battery with a new one. Continued use lf the Organizer with an exhausted

battery can alter or clear the memory contents.

Make sure the power is turned off before replacing the battery.

Do not press 

 until the battery replacement procedure is

completed.

Do not use a metalic object to pry out the battery. The Organizer
will be subjected to an electrical shock and all the memory con-
tents will be cleared.

Complete the replacement of the battery within 1 minute, other-
wise all the memory contents may be cleared.

1. Press 

  to turn the power off.

2. Loosen both screws and remove the battery

holder cover on the back of the unit.(Fig. 1)

3. Remove the exhausted battery by prying

 it out from the right holder with the corner of

the holder cover.(Fig 2)

4. Install a new battery with the positive side

(+) facing up into the right holder. (Fig. 1)

Do not install the battery into the left 
holder. It should be empty.

5. Replace the holder cover and secure it with

the screws.

6.Press 

  to turn the power on.

If nothing appears on the display, press the RESET switch.

When “RESET?” is displayed, press any key other than   SHIFT 

 ENTER  . Pressing   SHIFT    ENTER   clears all the memory con-

tents.

7. Set the clock.

Note)
Packing form

FORM

SPEC

Country

Blister

U1C

SEC, LAG, MEXICO, SECL

LL1

SUK, SCA, STCL

LN0

SEIS, SEES, SEZ, SEF

Universal

LM4

SEEG, SEA, SRS, SRSSC

LD0

SRH

LO0

SEMF, Agent

CAUTION FOR BATTERY REPLACEMENT

(Danish)

ADVARSEL !

Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English)

Caution !

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the equipment manufacturer.

Discard used batteries according to manufacturer’s instructions.

(Finnish)

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French)

ATTENTION

Il y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie du

même type ou d’un type recommandé par le constructeur.

Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

(Swedish)

VARNING

Explosionsfare vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

COPYRIGHT 

 1999 BY SHARP CORPORATION

All rights reserved.

Printed in Japan.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted.

In any form or by any means,

electronic, mechanical, photocopying, recording, or otherwise,

without prior written permission of the publisher.

SHARP CORPORATION
Information Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan

1999 June Printed in Japan 

OFF

ON

OFF

ON

Fig.1

Leave
empty

Fig.2

Leave
empty

OFF

ON

Reviews: