CD-SW200
8 – 7
IC701 RH-iXA056AWZZ: System Microcomputer (IXA056AW) (1/2
)
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Pin No.
Port Name
Terminal Name
Input/Output
Function
1
AVDD
AVDD
Input
Analog Power supply 5 V.
2-4
ANI0~ANI2
KEY 2-KEY 0
Input
Key 0~2 input.
5
ANI3
VOL_JOG
Input
Volume jog input.
6
ANI4
PROTECT
Input
Power abnormal detect.
7
ANI5
T_FP_SW
Input
Tape Fool Proof A&B SW.
8
ANI6
NO USE
Input
Connect to GND.
9
ANI7
T_RUN PULS
Input
Tape Run Pulse detect.
10
ANI8
DISC/CLAMP_SW
Input
5-Changer Disc SW & Clamp SW.
11
ANI9
TRAY_SW1&2
Input
5-Changer Tray SW 1&2.
12
ANI10
CD_INTB
Input
CS Servo interruption signal.
13
ANI11
MP3_INTB
Input
MP3 Servo interruption signal.
14
AVSS
AVSS
—
Analog ground.
15
VSS1
VSS
—
Ground voltage
16
X1
XIN
Input
Clock input
17
X2
XOUT
Output
Clock output.
18
VDD1
VDD
Input
Power supply 5 V.
19
VPP
VPP
—
Connect to GND.
20
P20
CD_CE
Output
CD chip enable.
21
SI0
CD_DO
Input
CD Data input.
22
SO0
CD_DI
Output
CD Data output.
23
SCK0
CD_CLK
Output
CD Clock.
24
INTP2
P_IN
Input
Power failure detect.
25
P66
PHOTO
Input
5-Changer Photo SW.
26
INTP1
SP_DET
Input
Speaker abnormal detect.
27
INTP0
REMOCON
Input
Remocon input.
28
P63
CE
Output
CE output.
29
P62
CLK
Output
Clock output.
30
P61
DI
Output
Data output.
31
P60
DO
Input
Data input.
32
P57
CD_RESOUT
Output
CD reset.
33
P56
MOTA+
Output
5-Changer Cam motor (+).
34
P55
MOTA-
Output
5-Changer Cam motor (-).
35
P54
TIMER LED
Output
Timer LED.
36
P53
S_MUTE
Output
System mute control.
37
P52
T_SOL_B
Output
Tape solenoid control.
38
P51
T_MOTOR
Output
Tape motor control.
39
P50
T_SOL_A
Output
Tape solenoid control.
40
VSS0
VSS
—
Ground voltage.
41
VDD0
VDD
Input
Power supply 5V.
42
RESET
RESET
Input
Reset input.
43
P47
ILLU_LED
Output
Illumination LED.
44
P46
NS_SW2
Output
New sound mode SW2.
45
P45
NS_SW1
Output
New sound mode SW1.
46*
P44
NO USE
Output
Open.
47*
P43
NO USE
Output
Open.
48*
P42
NO USE
Output
Open.
49*
P41
SP_LED
Output
Speaker LED.
50
P40
DIST
Input
Destination input.
51
P107
T_BIAS
Output
Tape record bias control.
52
P106
T_REC/PLAY
Output
Tape REC/PLAY control.
53
P105
T_T1/T2
Output
Tape 1/2 control.
54
P104
-20dBATT
Output
-20dB Attenuator.
55
P103
SP_RLY
Output
Speaker relay control.
56
P102
AC_RLY
Output
AC Relay control.
57-67
FIP41-FIP31
S30-S20
Output
FL Segment driver.
Summary of Contents for CD-SW200
